XAV-AX200/AX200C2
13
*1 Not supplied
*2 Speaker impedance: 4 Ω – 8 Ω × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a wired
remote control (not supplied).
For details on using the wired remote control, see “Using
the wired remote control” (page 29).
*5 Whether in use or not, route the microphone input cord
so it does not interfere with driving operations. Secure
the cord with a clamp, etc., if it is installed around your
feet.
*6 For details on installing the microphone, see “Installing
the microphone” (page 29).
*7 To connect a smartphone to the main unit, an
appropriate cable (not supplied) is required.
*8 To connect an iPhone, use the USB connection cable for
iPhone (not supplied).
*9
*10 For the navigation module XA-NV400 (not supplied)
If you have a power antenna (aerial) without a relay
box, connecting this unit with the supplied power
supply connection cable
ʓ
may damage the
antenna (aerial).
ɞ
To the car’s speaker connector
Making connections
1
Rear speaker
(right)
È
Purple
2
¾
Purple/black
striped
3
Front speaker
(right)
È
Gray
4
¾
Gray/black striped
5
Front speaker
(left)
È
White
6
¾
White/black
striped
7
Rear speaker
(left)
È
Green
8
¾
Green/black
striped
ʘ
Connection
*
3
*
3
*
3
Subwoofer*
1
Power amplifier*
1
ʘ
*
9
ʗ
Smartphone*
7
, iPhone*
8
,
USB device
from a wired remote control (not
supplied)
*4
ʕ
*
5
*
6
Light green
Purple/white striped
from a car antenna (aerial)
Rear view
camera*
1
For details, see “Making
connections” (page 28).
ʓ
*
3
*
3
*
3
*
3
Camera*
1
Camera*
1
Monitor*
1
See “Power connection diagram”
(page 29) for details.
*
2
(AEP, UK)
.
Cautions
• Run all ground (earth) leads to a common
ground (earth) point.
• Do not get the leads trapped under a screw or
caught in moving parts (e.g., seat railing).
• Before making connections, turn the car ignition
off to avoid short circuits.
• Connect the power supply lead
ʓ
to the unit and
speakers before connecting it to the auxiliary
power connector.
• Be sure to insulate any loose unconnected leads
with electrical tape for safety.
• Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
• Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature, such
as in direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other stereo
components, the amperage rating of the car circuit to which
the unit is connected must be higher than the sum of each
component’s fuse amperage rating.
Mounting angle adjustment
Adjust the mounting angle to less than 45°.
Connection/Installation
Precautions
.
for details.
ɟ
To the car’s power connector
ɠ
To the parking brake switch cord
The mounting position of the parking brake
switch cord depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply connection cable
ʓ
to the parking brake switch cord.
12
continuous power
supply
Yellow
13
power antenna (aerial) /
power amplifier control
(REM OUT)
Blue/white striped
14
switched illumination
power supply
Orange/white
striped
15
switched power supply
Red
16
ground (earth)
Black
.
ɡ
To the +12 V power terminal of the car’s rear
lamp lead (only when connecting the rear
view camera)
Memory hold connection
When the yellow power supply lead is connected,
power will always be supplied to the memory
circuit even when the ignition switch is turned off.
Speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 Ω to 8 Ω and
with adequate power handling capacities to avoid
damage.
Parking brake switch cord
Hand brake type
Foot brake type
SYS SET
2018/04/20 05:09:38 (GMT+09:00)
