background image

15

Specifications

Frequency range

774 to 798 MHz

Antenna input connectors

BNC-R type (1 each for antennas “a” and “b”)

Antenna output connectors

1)

BNC-R type (3 each for antennas “a” and “b”)

Antenna input/output impedance

50 ohms

Number of RF distribution

1)

3 distributions (TV channels 59 to 61) each for
antennas “a” and “b”

RF distribution loss

0 dB ±3 dB (distributed from the antenna input)

Power input connector

3-pin inlet (1)

Power supply for antenna boosters

DC 12V or 9V, or OFF (switchable),
supplied through the antenna input connectors

Power requirements

AC 220 to 240V, 50 Hz

Power consumption

16 W

Indications

1)

6 LEDs for antenna output connection indicators

Operating temperature

0°C to +50°C (+32°F to +122°F)

Recommended operating temperature

+15°C to +35°C (+59°F to +95°F)

Storage temperature

–10°C to +60°C (+14°F to +140°F)

Dimensions

482 

×

 44 

×

 300 mm

(19 

×

 1

3

/

4

 

×

 11

13

/

16

 inches) (w/h/d)

(including mounting brackets, but not feet)

Mass

Approx. 4.5 kg (9 lb 15 oz)

Accessories supplied

AC power cord (1)
Operating Instructions (1)

Design and specifications are subject to change without notice.

1)

Note:

This unit works only in the band between 774 MHz and
798 MHz (TV channels 59, 60, and 61).
The output connectors and LEDs (connection indicators)
with the markings 62, 63 and 64 have no functions.

.............................................................................................................................................................................................................................................................................................................................................................................................................

Summary of Contents for WD-880A

















Reviews: