background image

59

n

N

Precautions

Hardware Guide

On handling floppy disks

Do not open the shutter manually or touch the surface of the floppy disk.

Keep floppy disks away from magnets.

Keep floppy disks away from direct sunlight and other sources of heat.

On handling discs

Do not touch the surface of the disc.

Do not drop or bend the disc.

Fingerprints and dust on the surface of a disc may cause reading errors. Always hold the disc by its edge and central hole, as 
shown. 

Proper care of the disc is essential to its continuous reliability. Do not use solvents such as benzene, thinning agents, 
commercially available cleaners or anti-static spray, as they may cause damage to the disc.

For normal cleaning, hold the disc by its edge and use a soft cloth to wipe the surface from the centre out.

If the disc is badly soiled, moisten a soft cloth with water, wring it out well, and use it to wipe the surface of the disc from the 
centre out. Wipe off any remaining moisture with a dry soft cloth.

Never put stickers on discs. This will affect the use of the disc irreparably.

Summary of Contents for VAIO PCV-2251































































Reviews: