Sony UP-897MD, Instructions For Use Manual

Page: 47 / 218

Op
er
at
ion
Adjustments and Settings Using the Menu
47
LOAD To load the
registered settings LO:3: Loads the “SA:3”
settings registered using the
“SAVE” menu item.
LO:2: Loads the “SA:2”
settings registered using the
“SAVE” menu item.
[LO:1]
: Loads the “SA:1”
settings registered using the
“SAVE” menu item
BACK: Cancels the setting
change and returns to the
item selection column.
MEDIA To select the type
of paper ME:S: Uses the UPP-110S.
ME:HD: Uses the UPP-
110HD.
[ME: HG]
: Uses the UPP-
110HG
BACK: Cancels the setting
change and returns to the
item selection column.
MEMRY To select the
memory mode ME:FLD: When printing
fast-moving images (such
as a ball being thrown), the
printout may be blue. If this
happens, select this setting.
[ME:FRM]: Normally
select this setting.
BACK: Cancels the setting
change and returns to the
item selection column.
MENU To print the menu
settings currently
selected
[ME:OK]
: Prints the menu
list currently set.
BACK: Cancels printing
and goes back to its item
column.
MULTI To specify the
number of images
to be printed on
one sheet of the
printout MU:MLT: Prints two
images on one sheet of the
printout (two reduced
images).
[MU:SGL]: Prints one
image. (full-size image).
BACK: Cancels the setting
change and returns to the
item selection column.
PAGE
(This item is
not displayed
when
“MU:MLT”
is selected in
“MULTI.” Each time you
press the PRINT
button, the image
is stored in
memory. Up to
ten images can be
stored.
You can select the
desired image
from 10 kinds of
images stored in
memory and
make a printout.
[PG:1]
to PG:10: Prints by
selecting the desired ONE
image from among images
1 to10 and pressing the
COPY button.
BACK: Cancels the setting
change and returns to the
item selection column.
Item Function Settings
QTY To set the print
quantity
[QT:1]
to QT:9: Makes the
same printouts. You can
select the desired number of
same printongs between 1
and 9.
BACK: Cancels the setting
change and returns to the
item selection column.
SAVE To register up to
three kinds of
settings SA:3: Registers the menu
settings as No.3.
SA:2: Registers the menu
settings as No.2.
[SA:1]
: Registers the menu
settings as No.1.
BACK: Cancels the setting
change and returns to the
item selection column.
SCALE To enlarge or
reduce the image
to be printed The scale can be set
between SCL:2.0 (two
times) and SCL:0.5 (one
half) in increments of 0.5.
[SCL:1.0] is the factory
setting.
BACK: Cancels the setting
change and returns to the
item selection column.
SCAN
c)
To set the range
of the image to be
printed The range is widened in the
sequence of SC:NOR,
[SC:WD1]
and SC:WD2.
BACK: Cancels the setting
change and returns to the
item selection column.
SFT.H To specify the
horizontal
position of the
image to be
printed [S.H:0]: Adjusts the
horizontal position. The
numeric value displayed by
turning the jog dial depends
on the settings of
“SCALE”, “SCAN”, and
“SIDE”, and the signal
system of the image to be
captured.
BACK: Cancels the setting
change and returns to the
item selection column.
SFT.V To specify the
vertical position
of the image to be
printed [S.V:0]: Adjusts the vertical
position. The numeric value
displayed by turning the jog
dial depends on the settings
of “SCALE”, “SCAN”, and
“SIDE”, and the signal
system of the image to be
captured.
BACK: Cancels the setting
change and returns to the
item selection column.
Item Function Settings