background image

21

KV-25X5

Same Level

B-Out Waveform

JW130

11

TUNER

17

L103

IC101

RV101

A

A Board component side

25" 2.21V +/- 0.01V
29" 2.52V +/- 0.01V

R - out Waveform

SUB BRIGHTNESS ADJUSTMENT

1.

Input a Phillips colour pattern.

2.

Press ‘TEST’ ‘TEST’ 13 on the Remote Commander.

3.

Adjust the ‘Sub-Brightness’ data so that there is barely a 
difference between the 0 IRE and 10 IRE signal levels.

SUB CONTRAST ADJUSTMENT

1.

Input a video signal that contains a small 100% white area on a 
black background 

2.

Set the picture control to maximum. [‘TT01’]

3.

Connect an oscilloscope to Pin 1 of CN504 [A Board].

4.

Enter into the ‘Picture’ service menu.

5.

Adjust the ‘R - Drive’ data to obtain the following waveform.

SUB COLOUR ADJUSTMENT

1.

Receive a PAL colour bar signal.

2.

Connect an oscilloscope to Pin 3 of CN504 [A Board].

3.

Enter into the ‘Picture’ service menu.

4.

Adjust the ‘Sub Colour’ data so that the Cyan, Magenta and 
Blue colour bars are of equal levels as indicated below.

Note: Ensure that no signal is applied to the Antenna socket while 

carrying out the following IF adjustments.

SYSTEM B/G, D/K, I & L I.F ADJUSTMENT

1.

Input a 38.9Mhz carrier signal at 100dBuV to Pin 11 [IF 
output] of the tuner [TU101].

2.

Measure the voltage at Pin 17 of [IC101].

3.

Adjust L103 [A Board] to obtain a voltage of 2.5V +/- 0.3V.

SYSTEM L BAND 1 I.F ADJUSTMENT

1.

Input a 34.0MHz carrier signal at 100dBuV to Pin 11 [IF 
output] of the tuner [TU101].

2.

Select ‘system L’ + C00 [channel 00].

3.

Measure the voltage at Pin 17 [IC101].

4.

Adjust RV101 [A Board] to obtain a voltage of 2.5V +/- 0.3V.

TUNER AGC ADJUSTMENT

1.

Receive a signal of 65dBuV / 75 ohm terminated, via the tuner 
antenna socket.

2.

Connect a voltmeter to JW130 [A Board].

3.

Enter into the ‘Test Menu’. 

3.

Select the ‘AGC Adjust’ menu item.

4.

Adjust the data using the Yellow and Green buttons on the 
Remote Commander to obtain a voltage of 3.0V +/- 0.2V.

TECHNICAL

GD - Secam

30

BD - Secam

31

RC - Secam

11

GC - Secam

19

BC - Secam

10

GD - Sports 

30

BD - Sports 

36

RC - Sports 

14

GC - Sports 

15

BC - Sports 

17

Y - Delay (AV)

07

Summary of Contents for TRINITRON KV-25X5A



















































Reviews: