14
STR-DG710
KEY CHECK MODE
* Button check
* Procedure:
While depressing the
[SPEAKERS $OFF/A/B%]
and the
[2CH]
but-
tons simultaneously, press the
?/1
button to turn on the main
power.
Either the message “REST 14” appears.
Every pressing of any button other than the
?/1
counts down
the buttons. The buttons which are already counted once are not
counted again. When all buttons are pressed “REST 00” appears.
SWAP ALL MODE
* The signal will be swap to all channel so that all speaker will
have sound output.
* Procedure:
1. While depressing the
[SPEAKERS $OFF/A/B%]
and the
[A.F.D.]
buttons simultaneously, press the power
?/1
button to turn on
the main power.
2. “SWAP” appears. (No change while displayed.)
SHIPMENT MODE
All preset contents are reset to the default setting.
* Procedure:
1. While depressing the
[SPEAKERS $OFF/A/B%]
and the
[MUSIC]
buttons simultaneously, press the power
?/1
button to turn on
the main power.
2. “CLEARED” appears and switch off the set.
DCAC FACTORY TEST MODE
DCAC Factory Test mode have two stages:
1. DCAC DSP Data Line Checking
2. DCAC board Checking
Factory Test System Setup
1. When power off:
Press the three buttons
[MEMORY/ENTER]
+
[MOVIE]
+
?/1
.
“DCAC
[]
FTM” appears.
Afterward, press the
[TUNING MODE]
to start DCAC factory
test mode.
SECTION 3
TEST MODE
AM CHANNEL STEP 9 kHz/10 kHz SELECTION
MODE
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Turn the
[INPUT SELECTOR]
control to set AM and press the
?/1
button to turn off the main power.
While depressing the
[TUNING MODE]
button, press the
?/1
button to turn on the main power.
Either the message “9k STEP” or “10k STEP” appears for a
moment and select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same
time, then each segment lights on one after another.
* Procedure:
While depressing the
[TUNING MODE]
and the
[DISPLAY]
but-
tons simultaneously, press the
?/1
button to turn on the main
power.
1. ALL segments light on.
2. Turn the
[INPUT SELECTOR]
control, confirm display.
3. Turn the
[INPUT SELECTOR]
control, confirm display.
4. Turn the
[INPUT SELECTOR]
control, all segments light off.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon
completion of repair.
* Procedure:
While depressing the
[2CH]
button, press the
?/1
button to turn
on the main power.
The message “S.F. CLR.” appears for a moment and initializa-
tion is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed.
* Procedure:
While depressing the
[SPEAKERS $OFF/A/B%]
and the
[DISPLAY]
buttons simultaneously, press the
?/1
button to turn on the
main power.
The model name, destination and the software version are dis-
played for a moment.
L
SW
C
R
SL
S
SR
SBL
SB SBR
LFE
SP A
NEO:6
COAX
HDMI
DEX
DTS -ES
x
II
PL
RDS ST
CAT
96/24
MONO
D.RANGE
SAT
D D
D D
PL OPT
D D
dB
Hz
k
ft.
m
MHz
MEMORY
SP B
LFE
NEO:6
COAX
x
RDS
MONO
D.RANGE
k
m
MHz
SP B
SW
C
SL
SR
SBL
SB SBR
D
DTS
ST
CAT
D D
PL
D D
dB
Hz
ft.
MEMORY
DSP Data Line
Check
Start
Pass
Pass
Auto Cal Mic
Check
END
SPK Front Left
DCAC MIC
Receiver
