Sony STR-DA80ES - Fm Stereo / Fm-am Receiver, Operating Instructions Manual

Page: 9 / 40

9
Getting Started
Getting Started
TV/VCR Hookups
Overview
This section describes how to connect video
components to the receiver.
For digital connections, see “Digital Component
Hookups” on page 10.
AC OUTLET
IMPEDANCE
SELECTOR
SWITCHED 120W / 1A MAX
4 Ω 8 Ω
AC 120V 60Hz
CTRL A1
IN
FM
75
Ω
COAXIAL
S-LINK
FRONT SPEAKERS
+
R L R B A L
–
+
–
IMPEDANCE USE 4–16 Ω
REAR SPEAKERS
+
R L
–
+
–
IMPEDANCE USE 4–16 Ω IMPEDANCE USE 4–16 Ω
CENTER SPEAKER
AM
y
S VIDEO
IN
S VIDEO
IN
OUT
S VIDEO
OUT
S VIDEO
OUT
S VIDEO
IN
S VIDEO
IN
S VIDEO
OUT
VIDEO
IN
VIDEO
OUT
VIDEO
IN
VIDEO
OUT
VIDEO
IN
IN
L
R
L
R
L
R
REC OUT IN IN
AUDIO
IN
REAR
CENTER
WOOFER
FRONT
L
R
AUDIO
OUT
AUDIO
IN
AUDIO
OUT
AUDIO
IN
PHONO DAT / MD
MONITOR VIDEO 1 VIDEO 2 LD / DVD
VIDEO
IN
LD
DVD
AC-3 RF IN
AUDIO
IN
TV / DBS
CD
IN REC OUT
TAPE
SIGNAL
GND
y
LD
DVD
COAXIAL IN
LD
DVD
OPTICAL IN
TV
DBS
OPTICAL IN
CD
OPTICAL IN
DAT
MD
OPTICAL IN
DAT
MD
OPTICAL OUT
ANTENNA
DIGITAL
PRE OUT
VIDEO 2 MONITOR TV/DBS
*
LD/DVD VIDEO 1
*
TV/DBS: USA, Canadian, and Australian models
TV: other models
What cables will I need?
• Audio/video cable (not supplied) (1 for each TV or LD
player; 2 for each VCR)
Yellow Yellow
White (L) White (L)
Red (R) Red (R)
• Video cable (not supplied) (1 for a TV monitor)
Yellow Yellow
z
If you want to watch high quality video images
You can use an S-VIDEO cable for the TV/DBS, LD,
VIDEO 1/2/3, and MONITOR jacks.
Note
The signal input from the S VIDEO IN jack is not output to
the normal VIDEO OUT jack. Nor is the signal input from
the VIDEO IN jack output to the S VIDEO OUT jack.
Hookups
The arrow ç indicates signal flow.
TV or Digital Broadcasting System (DBS) tuner
DBS tuners can be used with the USA, Canadian, and
Australian models.
Receiver
TV or DBS tuner
Ç
L
R
L
R
OUTPUT
VIDEO
AUDIO
S VIDEO
IN
VIDEO
IN
AUDIO
IN
TV / DBS
(Continued)
If nominal impedance of
your speaker is
Set IMPEDANCE SELECTOR to
Set SPEAKERS selector to
8 ohms or higher
4
Ω
8
Ω
A
B
A+B
Between 4 and 8 ohms
To drive
Speaker system A (connected
to the FRONT SPEAKERS A
terminals)
Speaker system B (connected
to the FRONT SPEAKERS B
terminals)
Both speaker systems A and B
(parallel connection)
Selecting the speaker system
If you connect only one set of front speakers, set the
SPEAKERS selector on the front panel to A. If you
connect two sets of front speakers, see the following:
Selecting the impedance
Set the IMPEDANCE SELECTOR for the front speakers
as indicated in the table below. Check the instruction
manual of your speakers if you’re not sure of the
impedance. (This information is usually printed on a
label on the back of the speaker.)
z
To connect any speaker pair through an amplifier
Connect the amplifier to the PRE OUT jacks of the
receiver to output the PRE OUT jack signals from the
amplifier’s speaker terminals.
The signals output from the PRE OUT jacks are identical
to those output from the speaker terminals of the
receiver.
You can then connect any pair of speakers (e.g., the
front speakers) to the amplifier’s speaker terminals.