STR-DA5500ES
18
SPECIAL MENU MODE
Procedure:
1. Press the [POWER] button to turn on the main power, then while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A.
DIRECT], [MUSIC], [MOVIE (HD-D.C.S.)] button in order, the message “MENU SPECIALIZED !” appears.
2. Press the [
M
]/[
m
] buttons of the remote commander, the message “<<< SPECIAL >>>” appears.
3. Press the [
,
] button of the remote commander, the item is appears.
4. Each time the [
M
]/[
m
] buttons of the remote commander is pressed, the item is switched in order as follows.
Some items can change the content. Display the cursor by pressing the [
,
] button of the remote commander, and changing the content
by pressing the [
M
]/[
m
] buttons of the remote commander, and
fi
x the content by pressing the [
<
] button of the remote commander
when you want to change the content of the item.
5. To release from this mode, while pressing the [TONE MODE] button, press the [A.F.D.], [2CH/A. DIRECT], [MUSIC], [MOVIE (HD-
D.C.S.)] button in order again, the message “MENU SPECIALIZE OFF” appears.
Items
Display
Remark
SYSTEM version display
SYSTEM VERSION X.XXX
X.XXX: System software version
MAIN Ucom version display
MAIN #####
∗∗∗
vX. XX
#####: Model
∗∗∗
: Destination
X.XX: Main controller software version
Video Ucom version display
Video Ucom Ver X. XX
X.XX: Video system controller software version
FAROUDJA version display
FAROUDJA Ver X. XX
X.XX: Video processor software version
GUI CG-ROM version display
GUI CGROM Ver X. XX
X.XX: CG-ROM software version
DSP Ucom version display
DSP Ucom Ver X. XX
X.XX: DSP controller version
DSP serial
fl
ash version display
DSP SFLASH Ver X. XX
X.XX: DSP serial
fl
ash software version
DSP parallel
fl
ash version display
DSP PFLASH Ver X. XX
X.XX: DSP parallel
fl
ash version
IR learning Ucom version display
IR LEARNING Ver X.XX
X.XX: IR learning software version
Network processor version
NTE 09A55
∗∗
Ver X.XX
∗∗
: Destination
X.XX: Network processor software version
DSP debug menu
<DSP DEBUG MENU>
Not used for the servicing
Network debug menu
<NETWORK DEBUG MENU>
Menu mode to enter MAC address display. If the [ENTER] but-
ton of the remote commander is pressed, entering the menu,
and operating the following menu become possible
MAC address display
(Network debug menu)
MAC
∗∗
:
∗∗
:
∗∗
:
∗∗
:
∗∗
:
∗∗
∗∗
:
∗∗
:
∗∗
:
∗∗
:
∗∗
:
∗∗
: MAC address
Network update check
NET UPDATE CHECK?
If the [Enter] button of the remote commander is pressed, the
checking result is displayed without connecting to network. OK:
“NET UPDATE CHK OK”, Path to MAIN NG: “NET UPDATE
CHK NG M”, Path to VIDEO NG: “NET UPDATE CHK NG V”,
Path to DSP NG: “NET UPDATE CHK NG D”
Zone 4 display
ZONE 4 XXXXXXXX
Not used for the servicing
FAROUDJA update
FARO SELECT [XXXXXXX]
XXXXXXX: The selector is switched for the update of the
FAROUDJA update.
[VIDEO]: Video Ucom rewriting,
[UPDATE1]: Faroudja rewriting (main),
[UPDATE2]: Faroudja rewriting (2nd),
[DEBUG1]: Faroudja debug (main),
[DEBUG2]: Faroudja debug (2nd),
HDCP KEY READ [XXX]
Not used for the servicing
LEARNING TEST START?
Not used for the servicing
MODEL [#####
∗∗∗∗
XX]
Not used for the servicing
<VIDEO FACTORY MENU>
Menu mode to enter video calibration menu and DDR access
check menu If the [ENTER] button of the remote commander
is pressed, entering the menu, and operating two the following
menu become possible
www. xiaoyu163. com
QQ 376315150
9
9
2
8
9
4
2
9
8
TEL 13942296513
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
