Ad
dition
al I
n
fo
rm
atio
n
masterpage:Right
lename[E:\SEM_Janet\Revision
Data\J9050000_2580805131DA2100ES_US\2580805131\US09ADD_STR-DA2100ES-U.fm]
61
US
model name1[STR-DA2100ES]
[2-580-805-
13
(1)]
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem.
There is no sound or only a very low-level
sound no matter which component is
selected.
• Check that the speakers and components are
connected securely.
• Check that both the receiver and all components
are turned on.
• Check that you have selected the correct
component on the receiver.
• Check that MASTER VOLUME –/+ is not set at
“VOLUME –00dB”.
• Check that the SPEAKERS (OFF/A/B/A+B) is
not set to off (page 46).
• Check that the headphones are not connected.
• Press MUTING on the remote to cancel the
muting function.
There is no sound from a specific component.
• Check that the component is connected correctly
to the audio input jacks for that component.
• Check that the cord(s) used for the connection is
(are) fully inserted into the jacks on both the
receiver and the component.
• Check that you have selected the correct
component on the receiver.
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the PHONES
jack to verify that sound is output from the
headphones. If only one channel is output from the
headphones, the component may not be connected
to the receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both channels are
output from the headphones, the front speaker
may not be connected to the receiver correctly.
Check the connection of the front speaker which is
not outputting any sound.
• Make sure you have not connected only the L or R
jack to a monaural component. Use a monaural-
stereo cable (not supplied) and connect it to both
the L and R jacks. However, there will be no
sound from the center speaker when a sound field
(PRO LOGIC, etc.) is selected. When the center
speaker is set to “NO”, sound is output only from
front L/R speakers.
There is no sound from analog 2 channel
sources.
• Check that the DIGITAL ASSIGN function is not
used to assign the audio input of other input to the
selected input (page 35).
• Check that the INPUT MODE is not set to
“COAX FIXED” or “OPT FIXED” (page 36).
• Check that you have not selected MULTI CH IN
function.
There is no sound from digital sources (from
COAXIAL or OPTICAL input jack).
• Check that the DIGITAL ASSIGN function is not
used to assign the audio input of other input to the
selected input (page 35).
• Check that the INPUT MODE is not set to
“ANALOG FIXED” (page 36). Check that the
INPUT MODE is not set to “COAX FIXED” for
the sources from OPTICAL input jack, or set to
“OPT FIXED” for the sources from COAXIAL
input jack.
• Check that you have not selected MULTI CH IN
function.
• Check that “DEC. PRI. XXXX” in the
CUSTOMIZE menu is set to “DEC. PRI. AUTO”.
The receiver cannot decode the input signal (e.g.
DTS-CD) when set to “DEC. PRI. PCM”.
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected correctly and securely.
• Adjust balance parameters in the LEVEL menu.
There is severe hum or noise.
• Check that the speakers and components are
connected securely.
• Check that the connecting cords are away from a
transformer or motor, and at least 10 feet away
from a TV set or fluorescent light.
• Move your TV away from the audio components.
• Make sure you have grounded
U
SIGNAL GND
terminal (only when a turntable is connected).
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
There is no sound from the surround back
speakers.
• Some discs have no Dolby Digital EX flag even
though the packages have Dolby Digital EX
logos. In this case, select “SB DEC ON”
(page 34).
Troubleshooting
continued
US01COV_STR-DA2100ES-U.book Page 61 Wednesday, July 13, 2005 2:17 PM
