Sony SST-6420 Operating Manual Download Page 5

 

ATW             AWB

ATW             AWB

4.5.2 AWB mode-- Conventional auto white balance set the DIP SW to AWB 
position. In this case, operation is performed at a faster operating speed than 
ATW mode.       

 

5. Cautions: 

5.1. Never point the camera toward the sun 

Do not epose the lens directly to the sun or to strong light as this may damage 
the pick-ip device. 

5.2. Handle this camera with care 

Avoid any shock or bumping of the camera. Improper handling could damage 
the camera. 

5.3. Requires a proper operating environment 

This camera is designed for indoor use. The alloable temperature range for 

operation of this camra is between -10ºC ~ 50ºC and the allowable humidity is 

85%RH maximum. 

5.4. Clean the front face to the pick-up device 

It is recommended that the pick-up device surface be cleaned before lens 
installation or whenever the lens is changed. Cleaning should be done by 
using a chamois, a very find soft cloth, lens tissue or cotton tipped applicator 
and ethanol to carefully remove any fingerprint or dust. 

5.5. Check the power source voltage 

The power source voltage should be within the specified range. (Camera must 
meet the specifications). 

5.6. Objects and liquid entry 

Never push objects of any kind into this camra sa this may touch dangerous 
boltage points of short out parts that could result in a fire or electric shock. 
Never spill any kind of liquid on the video product. 

5.7. Servicing 

Do not attempt to service this video product by yourself as opening or 
removing covers may epost you to dangerous voltage or othe rhazards. Refer 
all service to qualified servicing personnel. 

5.8. Damage requiring service 

Unplug thi svideo product from the all outlet and refer service to qualified 
servicing personnel under the following conditions: 

1)  When the power supply cord or plug is damaged. 

2)  If liquid has been spilled, or objects has fallen into the video product. 

3)  If the video product has been exposed to rain or water. 

4)  If the video product has been dropped or the cabinet has been damaged. 

5)  When the video product exhibits a distince change in performance. 

-5 - 

Summary of Contents for SST-6420







Reviews: