background image

Help Guide

Wireless Speaker

SRS-XB31

Notes on waterproof and dust proof features

Waterproof and dust proof performance of the speaker

The speaker, with the cap fastened securely, has a waterproof specification of IPX7

*1

 as specified in “Degrees of

protection against water immersion” of the IEC60529 “Ingress Protection Rating (IP Code)”

*3

, and a dust proof

specification of IP6X

*2

 as specified in “Degrees of protection against solid foreign objects”

*3

.

Liquids that the waterproof performance specifications apply to

Applicable: fresh water, tap water, pool water, sea water
Not applicable: liquids other than the above (soapy water, water with detergent or bath agents, shampoo, hot spring
water, etc.)

The waterproof and dust proof performance of the speaker is based on our measurements under the conditions herein
described. Note that malfunctions as a result of water immersion or dust intrusion caused by misuse by the customer are
not covered by the warranty.

To avoid the deterioration of the waterproof and dust proof performance

Check the following and use the speaker correctly.

The speaker passes the drop test from 1.22 m (4 ft) on plywood of 5 cm (2 in) thickness conforming to MIL-STD 810
F Method 516.5-Shock. However, this does not guarantee no damage, no breakdown, or waterproof and dust proof
performance in all conditions. Deformation or damage from dropping the speaker or subjecting it to mechanical shock
may cause deterioration of the waterproof and dust proof performance.
Do not use the speaker in a location where large amounts of water or hot water may splash on it. The speaker does
not have a design that is resistant to water pressure. Use of the speaker in a location where high water pressure is
applied, such as under running water or in the shower, may cause a malfunction.
Do not pour high-temperature water or blow hot air from a hair dryer or any other appliance on the speaker directly.
Also, never use the speaker in high temperature locations such as in saunas or near a stove.
Handle the cap 

 with care. The cap plays a very important role in maintenance of the waterproof and dust proof

performance. When using the speaker, make sure that the cap is closed completely. When closing the cap, be
careful not to allow foreign objects inside. If the cap is not closed completely the waterproof and dust proof
performance may deteriorate and may cause a malfunction of the speaker as a result of water entering the speaker.

4-735-510-11(1) Copyright 2018 Sony Corporation

IPX7 equivalency: The speaker has been tested to and maintains its operability when gently submersed in water to a depth of 1 m (3 ft 3 7/8 in)
and left for 30 minutes.

*1

IP6X equivalency: The speaker has been tested to and continues to block dust after stirring for 8 hours in a testing device which contains dust
particles that are up to 75 μm in diameter.

*2

The supplied accessories are not waterproof or dust proof.

*3

73

Summary of Contents for SRS-XB31


























































































Reviews: