Sony SPP-A2470 Page 40 Operating Instructions Manual Download | Manualshive

Page: 40 / 72

background image

Answering Machine Features

40

US

Selecting the answering mode

You can set the answering machine to record
incoming messages (normal mode), or just
make an announcement without recording
messages (announcement only mode).
You can record your own greeting, or use the
factory pre-recorded greetings.

In the normal mode, you also have the option
of having a beep to tell you if you have
received any new messages.

Set AUDIBLE

When you wish to

Pre-recorded greeting

INDICATOR to

ON
(normal mode)

OFF
(normal mode)

ANN ONLY
(announcement only
mode)

Note

The same greeting is used regardless of the answering mode. Therefore, if you decide to change
the mode, make sure that you record a new greeting to match the answering mode.

When the memory is full

The maximum recording area of this phone’s memory is about 18 minutes* (including
the greeting, messages, and memo). If the remaining recording area becomes less than
one minute, “F” flashes on the display, and the phone automatically switches to
announcement only mode, which does not record messages, and the greeting will be
switched to the pre-recorded greeting.

* Available time for recording at NORM (Long) sound quality.

If you wish to record more messages, erase the existing messages (see page 45). You
can also erase the messages from an outside phone (see page 50).

Note

The time for the memory to become full depends on the REC. QUALITY switch setting.
“F” flashes on the display at the time which corresponds to the recording sound quality for the
latter setting, if the switch setting is changed during the operation.

play a greeting to ask the caller
to leave a message and have the
phone beep to alert you of
recorded incoming messages.

play a greeting to ask the caller
to leave a message but you do
not wish to sound a beep.

make an announcement to the
caller without accepting
incoming messages when, for
example, you are away on a
long vacation.

Preparing the answering machine (continued)

“Hello, I’m unable to answer
your call right now. Please call
again. Thank you.”

“Hello, I’m unable to answer
your call right now. Please leave
your name, number and
message after the tone.”

AUDIBLE
INDICATOR switch

«
...
38
39
40
41
42
...
»

Summary of Contents for SPP-A2470









































































Reviews:

No comments

Related manuals for SPP-A2470

Brand: Yealink Pages: 2

Brand: Talkswitch Pages: 26

Brand: Panasonic Pages: 92

Brand: Panasonic Pages: 16

Brand: Icom Pages: 75

Brand: Jabra Pages: 2

Brand: Jabra Pages: 2

Brand: Uniden Pages: 32

OpenScape Desk Phone CP400T

Brand: Unify Pages: 130

OpenScape Desk Phone CP100

Brand: Unify Pages: 36

Brand: Uniden Pages: 6

Brand: Altigen Pages: 6

Aegis-09 Series

Brand: Scitec Pages: 4

Brand: Uniden Pages: 22

Brand: Furuno Pages: 67

Brand: Wacker Neuson Pages: 44

Brand: Radio Shack Pages: 25

Brand: 3Com Pages: 130

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands