Sony ShowView SLV-SE740D Operating Instructions Manual Download

Page: 59 / 84

Setting the recording duration time

ditio

al Op

er
atio

Setting the recording duration time

After you have started recording in the normal way, you can have the VCR stop
recording automatically after a specified duration.

Before you start

…

• Refer to “Index to parts and controls” for button locations.

To extend the duration

Press

REC repeatedly to set a new duration time.

To cancel the duration

Press

REC repeatedly until the

indicator disappears and the VCR

returns to the normal recording mode.

To stop recording

To stop the VCR while recording, press

(stop).

Note

• You cannot display the current tape time in the display window when setting the

recording duration time.

While recording, press

REC.

The

indicator appears in the display window.

Press

REC repeatedly to set the duration time.

In SP mode

Each press advances the time in increments of 30 minutes.

In LP mode

Each press advances the time as shown below.

The tape counter decreases minute by minute to 0:00, then the VCR stops
recording and turns off automatically.

0:30

1:00

4:00

4:30

Normal recording

0:30

1:00

8:00

9:00

Normal recording

Summary of Contents for ShowView SLV-SE740D





















































































Search results

Summary of Contents for ShowView SLV-SE740D

Reviews:

Related manuals for ShowView SLV-SE740D

Brands by name

Popular brands

Sony ShowView SLV-SE740D, Operating Instructions Manual

Search results

Summary of Contents for ShowView SLV-SE740D

Reviews:

Related manuals for ShowView SLV-SE740D

Brands by name

Popular brands