Sony SDZ-S100 Operating Instructions Manual Download Page 6

Page: 6 / 64

Compatible Cartridges ..............................................35
Data Cartridge ............................................................35

Components and Functions........................................... 36

Setting the Write-protect Switch ..............................38
Cleaning Cartridge ....................................................38
Handling Cartridges ..................................................39
Usage, Storage, and Transport Environmental

Specifications .....................................................40

Appendix

Head Cleaning............................................................41
Changing the Air Filter Unit ......................................42
Hardware Reset .........................................................43
Updating the Firmware..............................................43
Taking Care of the Unit .............................................43

Safety ............................................................................ 43
Avoiding Damage ......................................................... 44

Troubleshooting ........................................................45
Specifications ............................................................47

Performance .................................................................. 47
Environmental Specifications ....................................... 47
Power Specifications/Miscellaneous............................. 48

Options .......................................................................48
Index ...........................................................................49

Trademarks

• Sony, Advanced Intelligent Tape, and Super Advanced Intelligent Tape are trademarks or registered trademarks of Sony

Corporation in this country, other countries, or both.

• Other product names are trademarks or registered trademarks of their respective owners in this country, other countries,

or both.

Summary of Contents for SDZ-S100

































































Search results

Summary of Contents for SDZ-S100

Reviews:

Brands by name

Popular brands

Sony SDZ-S100, Operating Instructions Manual

Search results

Summary of Contents for SDZ-S100

Reviews:

Brands by name

Popular brands