31
US
Additional Information
If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
There is no sound from the i.LINK S200
AUDIO OUT jack.
Is the i.LINK component selected by the input selector
on the connected amplifier?
,
Make sure the i.LINK component is selected by the
input selector on the connected amplifier. Refer
to the Operating Instructions supplied with the
amplifier.
Is the i.LINK function turned on?
,
See page 16. Press i.LINK to output signals from
the i.LINK S200 AUDIO OUT jack. When the
i.LINK function is on, i.LINK indicator lights up.
Is the i.LINK cord connected correctly?
,
Check the connection and connect the cord firmly.
Is the correct i.LINK cord used?
,
Make sure you use the i.LINK cord compatible
with i.LINK S200 (less than 3.5 meters).
Is the connection to the i.LINK component verified?
,
See page 7. Refer to the Operating Instructions
supplied with the component.
Are several i.LINK components connected?
,
There may be no sound when several i.LINK
components are connected.
There is no sound when beginning the playback.
,
According to the copy protection technology, no
sound is output while components are establishing
LINC.
There is no sound from the ANALOG OUT
jacks.
Is the i.LINK function turned on?
,
When the i.LINK function is on, no sound is
output from the ANALOG OUT jacks. Press
i.LINK to turn off the i.LINK indicator.
Is the input selector on the amplifier correctly set?
,
Set the input selector on the amplifier correctly to
output the sound from this player.
,
Make sure this player is connected to the correct
input jacks on the amplifier.
Is the connecting cord connected correctly?
,
Check the connection and connect the cord firmly.
There is no sound from the DIGITAL (CD)
OUT connectors.
Is the i.LINK function turned on?
,
When the i.LINK function is on, no sound is
output from the DIGITAL (CD) OUT jacks. Press
i.LINK to turn off the i.LINK indicator.
Is a Super Audio CD played back?
,
The audio signals of the Super Audio CD cannot
be output from the DIGITAL (CD) OUT
connectors.
Is “D. OUTPUT” in the menu set to “Off”?
,
Set “D. OUTPUT” to “On” (see page 24).
There is no sound from the SUB WOOFER
jack.
Do you select a playback mode which has subwoofer
output?
,
Select the playback mode so that the Sub woofer is
set to “
a
” (see page 25).
Do you play a disc which contains the LFE signal?
,
When you play a track that does not contain the
LFE signal, the signal outputs from the SUB
WOOFER jack only when you select “5 – Small +
SW” or “FRT – Large + SW” for the Multi-channel
playback mode (see page 25).
There is no sound from the headphones.
Is the i.LINK function turned on?
,
When the i.LINK function is on, no sound is
output from the PHONES jack. Use the
headphones output on your amplifier.
The disc does not play.
Is a correct disc inserted?
,
Make sure there is a disc inside the player.
,
Make sure the disc is not placed upside down on
the tray. Place the disc on the disc tray with the
label side up.
,
If the disc is placed at an angle, reload the disc.
,
If the disc is dirty, clean the disc (see page 30).
,
Make sure the disc is compatible with this player
(see page 15).
Moisture has condensed inside the player.
,
Remove the disc and leave the player turned on for
about an hour.
The remote does not function.
Are there any obstacles in the path of the remote and
the player?
,
Use the remote from the location you can see this
player.
The remote is not pointed at the remote sensor on the
player.
,
Point the remote at the remote sensor on the player.
Are the batteries in the remote weak?
,
Replace with new batteries.
Troubleshooting
Summary of Contents for SCD-XA9000ES - Es Super Audio Cd Player
Page 35: ......
