HCD-F200/F500
24
2. TEST MODES IN THE TEST MENU
These are the test modes done in the test menu.
Setting method of the test menu:
1. Press the [
?/1
] button to turn the power on.
2. Press the button in order of the [CLEAR]
[ENTER]
[0]
[1]
[0]
[ANGLE] on the remote commander. (Make
the interval when each button is pressed within two seconds.)
3. The message “TEST MENU” appears on the fl uorescent indi-
cator tube and enter the test menu.
2-1. Panel Test
Procedure:
1. Enter the test menu.
2. Press the [
M
] [
m
] button on the remote commander to select the
“PANEL TEST”, and press the [ENTER] button on the remote
commander.
3. All segments and all LEDs turn on. And half segment and ex-
cept front panel illmination LEDs turn on. then other half seg-
ment front panel illmination LEDs turn on.
4. When all segments in fl uorescent indicator tube are lighted up
in the state of step 3, press the [] button on the
remote commander and model information is displayed on the
fl uorescent indicator tube.
Each time the [] button on the remote commander
is pressed, the display changes from destination information,
MC version, SUB version in this order, and returns to the mod-
el information display.
Each time the [VOLUME –] button on the remote commander
is pressed, the version and date are switched.
5. In the state of step 3, press the [FUNCTION] button on the
remote commander and “K 0” is displayed on the fl uorescent
indicator tube.
“K 0” value increases whenever a button on the set is pressed.
However, once a button has been pressed, it is no longer taken
into account.
All buttons on the set are pressed, “OK” and “K 10” are alter-
nately displayed on the fl uorescent indicator tube.
6. To release from this mode, press the [
?/1
] button.
2-2. AMP Test
Procedure:
1. Enter the test menu.
2. Press the [
M
] [
m
] button on the remote commander to select the
“AMP TEST”, and press the [ENTER] button on the remote
commander.
3. The message “MEASURE” appears on the fl uorescent indica-
tor tube and enter the AMP test mode.
4. Press the [SUBTITLE] button on the remote commander, the
message “VACS ON” or “VACS OFF” appears on the fl uores-
cent indicator tube and thus the VACS on/off are changed.
5. To release from this mode, press the [
?/1
] button.
2-3. Cold
Reset
The cold reset clears data except DVD data stored in the RAM to
initial conditions. Execute this mode when returning the set to the
customers.
Procedure:
1. Enter the test menu.
2. Press the [
M
] [
m
] button on the remote commander to select the
“COLD RESET”, and press the [ENTER] button on the remote
commander.
3. The message “COLD RESET.” appears on the fl uorescent in-
dicator tube, then becomes standby states.
2-4. Product Out
Procedure:
1. Enter the test menu.
2. Press the [
M
] [
m
] button on the remote commander to select
the “PRODUCTOUT”, and press the [ENTER] button on the
remote commander.
3. After the “STANDBY” blinking display fi nishes, the message
“MECHA LOCK”
“UNPLUG” appears on the fl uorescent
indicator tube and the ship mode is set.
4. To release from this mode, pull out the power code.
2-5. DVD Service
This mode describes details in “3. DVD SERVICE MODE” (page
25).
2-6. Tuner Factory Preset
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
2-7. Digital Media Port Test
Procedure:
1. Connect the DMPORT check jig (P/N: J-2501-309-A) with the
DMPORT jack (CN3802) on the DMB-FIT board.
2. Press the [
?/1
] button to turn the power on.
3. Confi rm that both LEDs of the DMPORT check jig lights.
(Confi rmation the power supply line)
4. Press the [FUNCTION] button on the remote commander to
select the “DMPORT”.
5. Enter the test menu.
6. Press the [
M
] [
m
] button on the remote commander to select
the “DMPORT CHK”, and press the [ENTER] button on the
remote commander.
7. The message “DMPORT OK.” appears on the fl uorescent indi-
cator tube and enter the digital media port test mode. (Confi r-
mation of communication line)
When “NO DETECT.” and “UART .TO” are displayed on
the fl uorescent indicator tube, confi rm the connection of the
DMPORT check jig, and enter the mode again.
Each time the [
>
] button on the remote commander is
pressed, the connect check and adaptor version check are
switched.
Press the [
.
] button on the remote commander, connected
confi rmation of the DMPORT check jig is done again.
8. To a pinjack of the DMPORT check jig input information rele-
vant to audio signal (sine-wave 1.0V rms) and composite video
signal (white 100% 1.0Vp-p, color bar, etc.).
9. Confi rm the output of speakers and monitor TV. (Confi rmation
of analog signal)
10. To release from this mode, press the [
?/1
] button.
color
pattern
generator
DMPORT
check jig
(Part No.:
J-2501-309-A)
J001
AF
oscillator
set
(HCD-F200/
F500)
SA-WSF200/WSF500
TV
monitor
FL/FR
speaker
DMB-FIT board
CN3802
SPEAKER board
TB101 (SA-WSF500)
TB102 (SA-WSF200)
MAIN board
J906
