manualshive.com logo in svg

Sony PVM-14L1, Service Manual, Page: 33 / 76

Share
Download
Sony PVM-14L1 Service Manual Download Page 33

3-1

PVM-14L1/14L1MDE/20L1

SSM-14L1/20L1

Section 3

Safety Related Adjustment

This section explains the adjustment procedure when

safety related component(s) is replaced. Perform the

following adjustment when the safety related component(s)

is replaced.

[Preparation]

Equipment Required

. 

VG (programmable video signal generator)

VG-854 or equivalent

. 

DC power supply

. 

Digital VOM

Advantest TR6845 or equivalent

. 

Slide induction transformer

n

Start the following adjustments after 5 minutes have

passed after the main power is turned on.

When the parts (with a 

 mark on the circuit diagram)

shown below are replaced, confirm the matters described

in items 3-1 and 3-2 shown below.

A board

..... C101, C102, D102, D103, D312, D314, Q102,

Q314, Q315, Q316, Q317, R101, R107, R108,

R110, R311, R315, R316, R317, R318, T501 (FBT)

3-1. +B Voltage Check

1.

Supply the power source voltage of 127 to 130 V

AC

 to

the set and turn ON the power.

2.

Input the 480/60I all black signal, and adjust the

BRIGHT and CONTRAST knobs on the front panel to

MIN.

3.

Check that the +B voltage is 115.0 to 119.0 V

DC

.

+

B voltage measurement point

For 14-inch receiver :

Between T502 FBT pin-4 on A board and GND.

For 20-inch receiver :

Between T502 FBT pin-2 on A board and GND.

3-2. Protection Circuit Confirmation

3-2-1. HV Protector Circuit Confirmation

1.

Supply AC power voltage of 127 to 130 V

AC

 to the

unit and turn the POWER ON.

2.

Input the 480/60I all black signal, and adjust the

BRIGHT and CONTRAST knobs on the front panel to

MIN.

3.

Confirm that the voltage between the D103 cathode

(TP502) and GND on the A board satisfies the standard

value.

Standard value : 19.5 V

DC

 or more (14 inch)

23.5 V

DC

 or more (20 inch)

4.

Apply the following voltage between the D103

cathode and GND on the A board, and confirm that the

protector circuit is not activated.

23.1 to 23.5 V

DC

 (14 inch)

28.1 to 28.5 V

DC

 (20 inch)

5.

Apply the following voltage between the cathode

(TP502) and GND of D103 on the A board, and

confirm that the protector circuit is activated and raster

disappears.

25.3 to 25.5 V

DC

 (14 inch)

30.3 to 30.5 V

DC

 (20 inch)

Summary of Contents for PVM-14L1













































































Reviews:

No comments