Sony MV7101DS - Mobile DVD Dream System, Service Manual, Page: 9 / 34

9
MV-7101DS
MV-101
XVM-R70
XA-115
4
HEAD PHONE
V/L/R VIDEO 1
V/L/R VIDEO 2
V/L/R VIDEO 3
DC OUT
POWER
MONITOR OUT
DVD IN
REMOTE SIGNAL
V/L/R VIDEO OUT
PS One (optional)
2
8
1
2
3
4
1
5 m
(16.4 ft (pi))
ACC (5 m)
(16.4 ft (pi))
Fuse (8 A)
Fuse (1 A)
red
blue/white striped
Max. supply current 0.3 A
yellow
black
POWER REM 5 m (16.4 ft (pi))
RCA pin cord (optional)
3
4
Do not use the R (audio right)/L (audio left)/V (video)
output on the rear of the player.
black
Filter box
GND 1 m
(3.3 ft (pi))
GND 1 m
(3.3 ft (pi))
Cautions before connection
• The products are designed for negative ground 12 V
DC operation only.
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
after all other leads have been connected.
• Be sure to connect the red power input lead to the
positive 12 V power terminal which is powered when
the ignition switch is in the accessory position.
• Run all ground wires to a common ground point.
• The use of optical instruments with the player will
increase eye hazard.
• Use of controls adjustments or performance of
procedures of other than those specified herein may
result in hazardous radiation exposure.
Notes on the power supply cord (yellow)
• When connecting the player and the monitor in
combination with other stereo components, the
connected car circuit’s rating must be higher than the
sum of each component’s fuse.
• When no car circuits are rated high enough, connect
the products directly to the battery.
Connection diagram (
4
)
1 To a metal surface on the car
First connect the black ground lead, then
connect the yellow and red power input leads.
2 To the +12 V power terminal which is
powered at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
3 To the +12 V power terminal which is
powered when the ignition switch is in
the accessory position
Be sure to connect the black ground lead to a
metal surface of the car first.
Caution
If your car has no accessory position on the
ignition key, be sure to insulate and do not
connect the ACC lead (red) to anywhere. If you
connect the ACC lead according to the Operating
Instructions, it will cause the battery drain.
4 To POWER REMOTE IN of an optional
power amplifier
This connection is for amplifiers.
Notes
• If there is no accessory position, connect to the +12
V power (battery) terminal which is energized at
all times. Be sure to connect the black ground lead
to a metal surface of the car first.
• If you use the R (audio right)/L (audio left)/V
(video) output on the rear of the player, the
output level of video will be halved.
Cautions on installation of the
player MV-101
• Choose the mounting location carefully.
• Avoid installing the player in places:
— subject to temperatures below – 30 °C (– 22 °F) or
above 45 °C (113 °F)
— subject to direct sunlight.
— subject to heat;
Keep all products away from nearby hot vehicle
components that heat up over time such as hoses,
high current wires, and braking system
components. Make sure to leave enough room for
ventilation of openings and slots to protect from
over heating.
— near heat sources such as heaters.
— exposed to rain or moisture.
— exposed to excessive dust or dirt.
— subject to excessive vibration.
— where the fuel tank might be damaged by the
tapping screws.
— where wire harnesses or pipes might be under the
place.
— where the screws or the player itself might damage
the spare tire, tools, or other equipment in or
under the trunk.
— where the player might interfere with with the
normal movements of the driver.
— under the floor carpet, as the heat dissipation from
the player might damage the carpet.
• Be sure to use only the supplied mounting hardware
for a safe and secure installation.
• Use only the supplied screws.
• Make holes of ø 3 mm (
1
/
8
in) only after making sure
there is nothing on the other side of the mounting
surface.
• Do not install the player on inclined places. Install the
player on a level surface.
• Install the player just horizontally or vertically.
How to install the player
MV-101 (
5
)
When installing the player, choose the mounting
location carefully.
1
Place the player where you plan to install
it.
2
Mark the 4 positions for the holes of the
screws
7 on the surface of the mounting
board (not supplied).
The supplied mounting screws 7 are 15 mm
(
19
/
32
in) long, so make sure that the mounting
board is thicker than 15 mm ( 19 /
32
in).
3
Drill the 4 positions to make the holes of ø
3 mm (
1
/
32
in) in diameter.
4
Mount the player on the board (not
supplied) with the parts
5
and mounting
screws of
6
and
7
.