Sony LT39h Troubleshooting Manual Download Page 31 | Manualshive

Page: 31 / 63

background image

Troubleshooting Guide (mech)

1277-9814 Rev

2



Sony Ericsson Mobile Communications AB – Company Internal

31(63)

Problem Areas

1.14 GPS

1.14.1 GPS malfunctions

Check:

Inspect the antenna on Main Frame Assy and the contact
pins on Main PBA.

Action:

1. If dirty or oxidized – clean the pads and pins.

Check:

Replace the Main PBA with a known working one and test
the GPS.

Action:

1. If the GPS is still not working – Replace the Main Frame
Assy.

2. Replace the Main PBA.

«
...
29
30
31
32
33
...
»

Summary of Contents for LT39h
































































Reviews:

No comments

Related manuals for LT39h

Yealink SIP-T46G

Brand: Yealink Pages: 8

Brand: Uniden Pages: 141

Brand: i.safe MOBILE Pages: 258

Brand: TCM Mobile Pages: 37

Brand: UMI Pages: 44

Brand: EMPORIA Pages: 24

Ecom Smart-Ex 02

Brand: Pepperl+Fuchs Pages: 60

Brand: Trikdis Pages: 22

Brand: Pantech Pages: 213

Brand: Salora Pages: 33

Brand: Uniden Pages: 44

Brand: Samsung Pages: 128

SGH-T259 Series

Brand: Samsung Pages: 155

SGH-T229 Series

Brand: Samsung Pages: 140

SGH-T109 Series

Brand: Samsung Pages: 128

SGH-T159 Series

Brand: Samsung Pages: 173

Brand: Samsung Pages: 217

Brand: Samsung Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands