Sony KV-XA21M93 Service Manual Download

Page: 5 / 65

– 5 –

KV-XA21M93

RM-952

2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT

3. STOPPING THE STANDBY/TIMER FLASH

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp
from flashing.

4. SELF-DIAGNOSTIC SCREEN DISPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:

[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:

[Screen display]

channel

[5]

Sound volume

[-]

Power ON

Note that this differs from entering the service mode (mode volume

[+]

Self-Diagnosis screen display

STANDBY/SLEEP lamp

Lamp ON 0.3 sec.

Lamp OFF 3 sec.

Lamp OFF 0.3 sec.

2 times

3 times

Diagnostic Item

Flash Count*

+B overcurrent/overvoltage

2 times

Vertical deflection stopped

White balance failure

5 times

* One flash count is not used for self-diagnostic.

002 : 000
003 : 000
004 : 000
005 : 001

Numeral "0" means that no fault has been detected.

Numeral "1" means a fault has been detected.

101 : 000

SELF DIAGNOSTIC

Summary of Contents for KV-XA21M93


































































Search results

Summary of Contents for KV-XA21M93

Reviews:

Related manuals for KV-XA21M93

Brands by name

Popular brands

Sony KV-XA21M93, Service Manual

Search results

Summary of Contents for KV-XA21M93

Reviews:

Related manuals for KV-XA21M93

Brands by name

Popular brands