background image

– 22 –

KV-HA14M80/HA14M90

RM-969

No NICAM

1 = NICAM search is disable in any TV system, 0 = NICAM search operates

US ST

(Reserved for NTSC model)

1 V-Curve

1 = using common volume curve for every mode and every TV system

(for monaural model)

0 = another volume curve available for video mode and M system

XTAL SEL

00 = only 4.43 XTAL

01 = only 3.58 XTAL

10 = not used

11 = both 4.43 and 3.58 XTAL

Other optional function will be enabled if the corresponding bit is set to 1.

No. 50 OP3

No Bal.

1 = no balance in analog select items, 0 = balance included

(for AV stereo model)

SPC SOUND

1 = Space Sound available, 0 = not available

Korean ST

(Reserved for NTSC model)

H.K. Bil.

1 = NICAM bilingual available (No NICAM stereo), 0 = not available

(for monaural model)

Other optional function will be enable if the corresponding bit is set to 1.

No. 4F OP2

Item

KV-HA14M80

KV-HA14M90

Thai Bil.

0

0

H.K. Bil.

0

1

VM

0

0

Korean ST

0

0

SPC SOUND

1

1

No Bal.

0

0

Auto TV Sys.

0

0

Pict Rot.

0

0

Item

KV-HA14M80

KV-HA14M90

2nd Lang.

1

1

SECAM

1

1

IV-Curve

0

0

HDEV

0

0

US ST

0

0

No NICAM

0

0

XTAL SEL

11

11

11

11

Summary of Contents for KV-HA14MXX






















































Reviews: