– 68 –
KV-EX29M87/EX29N93
RM-963
RM-966
7-4. DEFLECTION ADJUSTMENTS (KV-EX29M87)
FOR DRC 1250 (50Hz) MODE
1.
Set to Service Mode.
2.
Input a Pal cross hatch/dot signal.
3.
Set the following condition.
Picture Mode to
[DYNAMIC]
, Picture Rotation to
[+/–0]
and
Eco Mode to OFF.
4.
Set to DRC-MF1250 mode.
5.
Using the
[1]
and
[4]
button, select category GEO (Service
Mode).
6.
Raise/lower the data using the
[3]
and
[6]
buttons.
Select and adjust the following items to obtain optimum
image.
Service Item
GEO : 00
VSZ
V SIZE
01
VPS
V POSITION
02
VLN
V LINEARITY
03
SCO
S CORRECTION
04
HSZ
H SIZE
06
PAP
PIN AMP
07
UPN
UPPER CORNER PIN
08
LPN
LOWER CORNER PIN
09
TRZ
TRAPEZIUM
0A
AGL
AFC ANGLE
0B
BOW AFC BOW
7.
Using the
[1]
and
[4]
buttons select category DAC (Service
Mode).
8.
Select and adjust the following items to obtain optimum
image. Raise/lower the data with the
[3]
and
[6]
buttons.Select and adjust the following items to obtain
optimum image.
Service Item
DAC: 01
HLN
H LINEARITY
04
HTR
HORIZONTAL TRAPEZIUM
05
PBA
PIN UNBALANCE
9.
Select “GEO 04 HSZ” with the
[1]
and
[4]
buttons.
10.
Confirm the H Size condition. If necessary, adjust the H
Size to get a best condition.
11.
Write into the memory by pressing
[MUTING]
then
[0]
on
the remote commander.
FOR WIDE MODE, DRC1250 (50Hz)
12.
Adjust condition change to WIDE MODE : ON.
13.
COPY (item FOR DRC 1250 (50Hz) MODE and adjust
data for the following items.
Service Item
GEO : 00
VSZ
V SIZE
01
VPS
V POSITION
04
HSZ
H SIZE
14.
Adjust V Blanking the following items.
Service Item
GEO : 13
VAS
V ASPECT
14
VSC
V SCROLL
15.
Adjust the following items.
Service Item
GEO : 02
VLN
V LINEARITY
03
SCO
S CORRECTION
05
HPS
H POSITION
06
PAP
PIN AMP
07
UPN
UPPER CORNER PIN
08
LPN
LOWER CORNER PIN
09
TRZ
TRAPEZIUM
0A
AGL
AFC ANGLE
0B
BOW AFC BOW
DAC : 01
HLN
H LINEARITY
04
HTR
HORIZONTAL TRAPEZIUM
05
PBA
PIN UNBALANCE
16.
Repeat step 5 and 6.
FOR DRC 1250 (60Hz) MODE
17.
Input 525/60Hz signal.
18.
Set to DRC-MF : 1250
19.
COPY
"DAC 00 HCT (DRC 1250, 50Hz)"
to
"DAC 00 HCT (DRC 1250, 60Hz)"
20.
Adjust the Service Item listed in no. 6 and no. 8.
FOR WIDE MODE, DRC 1250 (60Hz)
21.
Set to WIDE MODE : ON
22.
Using the
[1]
and
[4]
buttons select category GEO (Service
Mode).
23.
Select and adjust the following items to obtain optimum
image.
Raise/lower the data with the
[3]
and
[6]
buttons.
GEO
00
VSZ
V SIZE
01
VPS
V POSITION
04
HSZ
H SIZE
24.
Adjust V Blanking for the following items
GEO
13
VAS
V ASPECT
14
VSC
V SCROLL
25.
Adjust the Service Item listed in no.15.
26.
Repeat step 5 and 6
27.
Input a NTSC cross hatch/dot signal and repeat all above
steps.
7-5. A BOARD ADJUSTMENT AFTER IC003
(MEMORY) REPLACEMENT
1.
Enter to Service Mode.
2.
Press commander buttons
5
and
-
(Data Initialize), and
2
and
-
(Data Copy) to initialize the data.
3.
Call each item number and check if the respective screen
shows the normal picture.
In cases where items are not well adjusted, rectify the items
with fine adjustment.
Write the data per each item number (
[MUTING]
+
-
).
4.
Select item numbers “OPB00” (OP1), “OPB01” (OP2) and
respectively set the bit per model with command buttons
3
and
6
.
5.
Press commander buttons
8
and
-
(Test Normal) to return
to the data that was set on the shipment from the factory.
(This will also cancel Service Mode.)
