Sony IT-M804 Operating Instructions Manual Download

Page: 27 / 80

Getting Started

Getting Started

Lamp indications

Lamp/button

Lighting pattern

Status

Lights up OFF

INTERCOM

Lights up

Calling extension from your phone or
conversation available.

Flashes

Receiving an intercom call.

Flashes

Other phone using extension.

CONF

Lights up

This function is activated.

NEW CALL

Flashes

There is new data in the Caller ID list.

MESSAGES

Flashes

There are voice mail messages.

LOWER

Lights up

Selecting the second memory of the
one-touch dial button.

LINE 1 to 4

Lights up

You are using this line.

Flashes

Receiving a call.

Flashes

Call being held on your phone line or
transferred call being made.

Flashes

Call being held on other phone line.

Flashes

Receiving a transferred call.

Flashes

Line is used by other phone.

BUSY REDIAL

Lights up

This function is activated.

MUTING

Lights up

This function is activated.

DO NOT DISTURB

Lights up

This function is activated.

SPEAKERPHONE

Lights up

Talking through the speakerphone or

(HEADSET)

headset, paging or busy redialing.

rg
rh

Summary of Contents for IT-M804

















































































Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands

Sony IT-M804, Operating Instructions Manual

Search results

Summary of Contents for IT-M804

Reviews:

Related manuals for IT-M804

Brands by name

Popular brands