A
B
C
Network cable
(straight,
not supplied)
AC adaptor
10BASE-T/
100BASE-TX
Hub
Network
To power
socket
To an analog monitor
IPELA HYBRID-compatible
camera
Coaxial cable
Coaxial cable
To a keyboard
I/O port
connector
D
Unit: mm (inches)
250 (9
7
/
8
)
210 (8
3
/
8
)
44
(1
3
/
4
)
Location and Function of Parts
Front
POWER indicator (green)
When the receiver receives power, an internal system check is performed.
The indicator lights up when the unit is operating normally.
NETWORK indicator (green/orange)
The indicator lights up or flashes when the unit is connected to the network. The
indicator remains off when the unit is not connected to the network.
When connecting the unit via 100BASE-TX, the indicator lights up in green. When
connecting the unit via 10BASE-T, the indicator lights up in orange.
SLOC indicator (orange)
The indicator lights up in orange when an SLOC connection to a hybrid camera is
established.
The indicator flashes in orange when an SLOC transmission error is occurring.
Rear
Video output terminal (BNC)
Outputs composite video signals.
DC IN 12 V DC (power input) terminal
Connect to the supplied DC 12 V AC adapter.
SLOC (IP coaxial transfer) port
Use this terminal to connect the unit to an IPELA HYBRID-compatible camera via a
coaxial cable.
Reset switch
To restore the unit’s default settings, press this switch using a pointed object and turn
the power on while the switch is pressed.
RS-485 selection switch
Set this switch to ON to enable network functions; this unit’s settings can then be
changed over the network that is connected via the LAN port. This unit’s Serial PTZ
functions are also enabled; the unit can accept input from the keyboard connected to
this unit’s I/O port.
Set this switch to OFF to disable network functions and block input from the I/O port.
After switching, it is necessary to turn the power off and on again, to enable the
setting.
I/O (input/output) port
This unit includes an RS-485 port. You can connect a keyboard that is compatible with
Pelco-D protocol control signals in order to control the unit.
Indication
Function
NC
+
RS-485 (+) input/output (GND level reference)
–
RS-485 (–) input/output (GND level reference)
G
RS-485 reference GND
LAN (network) port (RJ-45)
Connect to a 10BASE-T or 100BASE-TX network using a network cable.
CAUTION
For safety, do not connect the connector for peripheral device wiring that might
have excessive voltage to this port. Follow the instructions for this port.
When you connect the LAN cable of the unit to peripheral device, use a
shieldedtype cable to prevent malfunction due to radiation noise.
Connection
Connecting to the Network
Connect to the network router or hub via this unit’s LAN port, using a network cable
(not supplied).
Connecting to a Monitor
Connect a video output terminal of the unit to an analog monitor using a coaxial cable
(not supplied).
Connecting to an IPELA HYBRID-compatible Camera
Connect a SLOC port of the unit to an IPELA HYBRID-compatible camera’s SLOC port
using a coaxial cable (not supplied).
The maximum coaxial cable length is RG-59 300 m.
Note
The high-frequency characteristics of coaxial cables may differ, even if the cables are of
the same classification. Use a high-quality, high-frequency coaxial cable with this unit.
For details on coaxial cables and cameras that can be connected to this unit, refer to the
instruction manual of the connecting SLOC device. For further details, please consult an
authorized Sony dealer.
Connecting to a Keyboard
Using the supplied I/O port connector, connect a keyboard (not supplied) that
supports the Pelco-D protocol, and set the RS-485 selection switch to ON.
The RS-485 selection switch is set to OFF in the factory default settings.
Set the RS-485 selection switch of only SNCA-ZX104 units with a keyboard connected
to ON.
For details on settings related to the Serial PTZ function and settings related to connecting
the keyboard, refer to the User’s Guide.
For details on camera settings related to Serial PTZ, refer to the camera’s Instruction
Manual.
Connecting the Power Source
Connect to the supplied DC 12 V AC adapter.
Specifications
Interface
SLOC input
BNC ×4, 75Ω termination
Analog video output
BNC ×4, composite 1.0 Vp-p, 75Ω termination
Network port
10BASE-T/100BASE-TX, auto negotiation (RJ-45)
I/O port
Camera control interface: ×1 (RS-485)
Others
Power supply
DC 12V
Consumption current
0.8 A
Operating temperature
0 °C to 45 °C (32 °F to 113 °F)
Storage temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Operating humidity
20% to 80% (no condensation)
Storage humidity
20% to 80% (no condensation)
Dimensions
210 × 44 × 250 mm (8
3
/
8
× 1
3
/
4
× 9
7
/
8
in) (w/h/d)
(without the projecting parts)
Mass
Approximately 1.1 kg
Supplied accessories
CD-ROM (User’s Guide and supplied programs) (1)
Installation Manual (this document) (1)
B&P Warranty Booklet (1)
AC adaptor (AC-NB12A) (1)
I/O port connector (1)
Note
This package may contain additional installation
manuals and/or documentation.
AC adaptor (AC-NB12A)
Power supply
AC 100 to 240 V, 50/60 Hz
0.65 A to 0.35 A
Output
DC 12 V, 2.5 A
Operating temperature
0 °C to 45 °C (32 °F to 113 °F)
Operating humidity
20% to 80% (no condensation)
Storage temperature
–20 °C to +60 °C (–4 °F to +140 °F)
Storage humidity
20% to 80% (no condensation)
Dimensions
49.5 × 28 × 99.5 mm (2 × 1
1
/
8
× 4 in) (w/h/d) (without
the projecting parts)
Mass
Approximately 0.2 kg (7 oz)
Design and specifications are subject to change without notice.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it inspected
periodically for safe use.
It may appear flawless, but the components may have deteriorated over time, which
may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.
NOTICE TO USERS
© 2012 Sony Corporation. All rights reserved. This Installation Manual, in whole or in
part, may not be reproduced, translated or reduced to any machine readable form
without prior written approval from Sony Corporation.
SONY CORPORATION PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL,
THE UNIT OR OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY
DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE WITH REGARD TO THIS MANUAL, THE UNIT OR SUCH OTHER
INFORMATION. IN NO EVENT SHALL SONY CORPORATION BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT,
CONTRACT, OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS
MANUAL, THE UNIT OR OTHER INFORMATION CONTAINED HEREIN OR THE USE
THEREOF.
Sony Corporation reserves the right to make any modification to this manual or the
information contained herein at any time without notice.
“IPELA”,
and
are trademarks of
Sony Corporation.
Adobe and Adobe Reader are trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
sloc™ is a trademark owned by the Intersil Corporation family of companies.
All other company and product names are trademarks or registered trademarks of
the respective companies or their respective makers.