English
Location and Function of Part
Front
Lens
A fixed-focus lens is mounted.
Tripod screw hole
Use this screw hole when attaching the camera
to a tripod (screw: 1/4”, 20 UNC). You can attach a
tripod to either the top or bottom of the camera.
Caution
Use the mounting screw whose length is 4.5 mm (³/₁₆ inch) –
7 mm (⁹/32 inch) only. Use of other screws may cause improper mounting
and damage parts inside the camera.
Model name label
This label shows device information, such as the model name and serial
number.
Rear
LAN connector (PoE) [RJ-45]
Use the network cable (UTP, category-5) for network communications and
PoE* power supply.
See “connect to network” for connection.
(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard compliant
devices.)
Fall-prevention rope mounting hole
When installing the camera on a ceiling or a wall. Be sure to secure a fall-
prevention rope (not supplied) to this hole for safety.
MONITOR out connector [AV minijack]
Output the composite video signal from the camera.
Monitor out is used when you adjust the angle of view. Be sure to set monitor
out to on when you use it. Set it to off and disconnect the AV cable when you
do not use it.
For details on system setting, see the User’s Guide.
Note
Be aware that the system performance may be influenced, if monitor out
is set to on. Be sure to set it to off and disconnect the AV cable when you
do not use it.
NTSC/PAL switch
Switching the video output.
Sensor input
Sensor input
cable color
Signal
Red
Sensor input+
White
Sensor input– (GND)
For details on function and required settings, refer to the User’s Guide
stored in the supplied CD-ROM.
For the wiring, see “Wiring diagram for sensor input”.
POWER indicator (Green)
When the power is supplied to the camera, the camera starts checking the
system. If the system is normal, this indicator lights up.
NETWORK indicator (Green/Orange)
The indicator lights up or flashes when the camera is connected to the
network. The indicator is off when the camera is not connected to the
network. When 100BASE-TX is connected, the indicator turns green. When
10BASE-T is connected, the indicator turns orange.
Reset switch
To reset the camera to the factory default settings, turn on the power to the
camera while holding down this switch with a pointed object.
Mac address label
Indicates the Mac address of this camera.
Installation
Caution
When installing the camera on a ceiling or a high location, be sure to secure a
fall-prevention rope (not supplied) to the camera for safety.
Attaching the fall-prevention rope
When you install the camera on a ceiling or a high location, be sure to attach a
fall-prevention rope (not supplied) to prevent the camera from falling. Thread
the fall-prevention rope through the hole on the rear of the camera, and then fix
it to the junction box on the ceiling or wall with a screw (not supplied), as in the
illustration.
For details about the fall-prevention rope, please consult the store of purchase or
an authorized Sony dealer.
Note
Take care to avoid any short-circuits with the rope when you attach it.
Connection
Connect to the Network
Connect the LAN connector of the camera to a PoE* supported device (such as a
hub) using the network cable (straight, not supplied).
The electrical power is supplied through the network cable. For details, refer to
the instruction manuals of the PoE supported devices.
(* PoE: The acronym for Power over Ethernet. IEEE 802.3af standard compliant
devices.)
Wiring diagram for sensor input
Mechanical switch/open collector output device
Camera inside
Outside
or
GND
Mechanical
switch
Open collector
output device
3.3 V
2.2 kΩ
Sensor input −
(GND)
10 kΩ
GND
GND
10 kΩ
10 kΩ
Sensor input +
Using the front sheet
If you want to turn the front logo upside down (for correct orientation after
installation), use the supplied front sheet (with logo).
If you want to hide front logo, use the supplied front sheet (without logo).
U1/4”, 20 UNC
= 4.5 mm - 7 mm
(ISO standard) (with the
screws fastened)
U1/4”, 20 UNC
= 4.5 mm - 7 mm
(ISO standard) (with the
screws fastened)
Specifications
Compression
Video compression format
JPEG/MPEG4/H.264
Maximum frame rate
JPEG/MPEG4/H.264: 30 fps (1280 × 720)
Camera
Image device
1/2.8type CMOS (Exmor)
Effective picture elements: Approx. 3,270,000
Minimum illumination
2.0 lx (AGC (max.)/50 IRE (IP))
Lens
Focal length
3.3 mm
Maximum relative aperture
F2.8
View angle
Horizontal: 88° / Vertical: 65° (4:3 mode)
Minimum object distance
0.5 m
Interface
LAN (PoE)
10BASE-T/100BASE-TX, auto negotiation RJ-45
Sensor input
1 port: make contact and break contact switchable
Monitor out
NTSC/PAL
1.0 Vp-p, 75 ohms, unbalanced, sync negative
AV minijack*
* Use AV cable with mini-plug at AV4 terminal.
Others
Power
IEEE802.3af compliant (PoE system) Class 1
Power consumption
2.4 W
Operating temperature
0°C~50°C (32°F to 122°F)
Storage temperature
–20°C to +60°C (–4°F to +140°F)
Operating humidity
20% to 80% (Non-condensing)
Storage humidity
20% to 95%
Dimensions (diameter × length)
ø
44 mm × 93 mm (1 3/4 inches × 3 3/4 inches)
Mass
Approx. 100 g (4 oz)
Supplied accessories
CD-ROM (User’s Guides, and supplied programs) (1)
Sensor input cable (1)
Front sheet (with logo) (1)
Front sheet (without logo) (1)
Installation Manual (this document) (1)
Design and specifications are subject to change without notice.
Recommendation of Periodic Inspections
In case using this device over an extended period of time, please have it
inspected periodically for safe use.
It may appear flawless, but the components may have deteriorated over time,
which may cause a malfunction or accident.
For details, please consult the store of purchase or an authorized Sony dealer.
中文
各部件位置和功能
正面
镜头
安装定焦镜头。
三脚架螺丝孔
将摄像机安装到三脚架上时使用此螺丝孔（螺丝：
1/4”，20 UNC）。您可以将三脚架安装在摄像机的
顶部或底部。
注意
只能使用长度为 4.5 mm - 7 mm 的安装螺丝。使用其它螺丝可能会造
成不当安装，并可能损坏摄像机内部零件。
型号标签
此标签表示设备信息，例如型号和序列号。
背面
LAN 接口（PoE） [RJ-45]
使用网线（UTP、5 类）进⾏网络通讯和 PoE
*
供电。
关于连接，请参见“连接至网络”。
（
*
PoE：Power over Ethernet 的缩写。符合 IEEE 802.3af 标准的设
备。）
防掉落钢绳安装孔
将摄像机安装在天花板或墙上时。出于安全，必须将防掉落钢绳（不附
带）固定在此孔中。
MONITOR 输出接口 [AV 迷你插孔]
输出来⾃摄像机的复合视频信号。
显示器输出用于调节视角时。务必在使用时将显示器输出设定为开。不使
用时，请设定为关并断开 AV 电缆的连接。
关于系统设定的详情，请见用户指南。
注意
请注意，如果显示器输出设定为开，系统性能可能会受影响。不使用
时，请务必设定为关并断开 AV 电缆的连接。
NTSC/PAL 开关
切换视频输出。
传感器输⼊
传感器输⼊
电缆颜色
信号
红色
传感器输⼊ +
⽩色
传感器输⼊ - (GND)
有关功能和所需设定的详情，请参见附带 CD-ROM 中存储的用户指
南。
关于布线，请参见“传感器输⼊布线图”。
POWER 指示灯（绿色）
当摄像机通电时，摄像机便开始检查系统。如果系统正常，则该指示灯
亮起。
NETWORK 指示灯（绿色/橙色）
摄像机连接至网络时，指示灯点亮或闪烁。摄像机未连接至网络时，指
示灯熄灭。连接了 100BASE-TX 时，指示灯变为绿色。连接了 10BASE-T
时，指示灯变为橙色。
复位开关
若要将摄像机复位至出⼚默认设定，请用尖头物体顶住此开关打开摄像机
电源。
Mac 地址标签
表示本摄像机的 Mac 地址。
U1/4”, 20 UNC
= 4.5 mm - 7 mm
濃JTP!㝫K濄)圞ᶁ⡨
ᷲ㉋䲋䈚⽥濄
U1/4”, 20 UNC
= 4.5 mm - 7 mm
濃JTP!㝫K濄)圞ᶁ⡨
ᷲ㉋䲋䈚⽥濄
Rope (not
supplied)/
防掉落钢绳
（不附带）
Network cable
(straight, not
supplied)/
网线（直通，
不附带）
10BASE-T/
100BASE-TX
PoE supported device
(such as a hub)/
PoE 支持设备（例如
集线器）
Front/
正面
Unit: mm (inches)/
单位：mm（英寸）
Top/
顶部
46 (1
13
/
16
)
93 (3
3
/
4
)
安装
注意
将摄像机安装到天花板或较高的位置时，出于安全，必须将防掉落钢
绳（不附带）固定在摄像机上。
安装防掉落钢绳
将摄像机安装在天花板或较高位置时，必须安装防掉落钢绳（不附
带），以防止摄像机掉落。如图所示，将防掉落钢绳穿过摄像机背面的
孔，然后用螺丝（不附带）固定于天花板或墙上的接线盒。
有关防掉落钢绳的详情，请向购买商店或授权 Sony 经销商咨询。
注意
连接时请⼩⼼，以免与钢绳发⽣短路。
连接
连接到网络
使用网线（直通，不附带）将摄像机的 LAN 接口连接至 PoE
*
支持设备
（例如集线器）。
电源由网线提供。有关详情，请参见 PoE 支持设备的使用说明书。
（
*
PoE：Power over Ethernet 的缩写。符合 IEEE 802.3af 标准的设
备。）
传感器输⼊布线图
机械开关/集电极开路输出设备
摄像机内部
外部
或
GND
机械开关
集电极开路
输出设备
3.3 V
2.2 kΩ
传感器输⼊ -
(GND)
10 kΩ
GND
GND
10 kΩ
10 kΩ
传感器输⼊ +
使⽤正面贴片
如果您要将正面标识颠倒（为了使安装后⽅向正确），请使用附带的正
面贴片（带标识）。
如果您要隐藏正面标识，请使用附带的正面贴片（不带标识）。
规格
压缩
视频压缩格式
JPEG/MPEG4/H.264
最⼤帧频
JPEG/MPEG4/H.264: 30 fps（1280 × 720)
摄像机
成像元件
1/2.8 型 CMOS（Exmor)
有效像素：约 3270000
最低照度
2.0 lx（AGC (最⼤)/50 IRE（IP))
镜头
焦距
3.3 mm
最⼤相对光圈
F2.8
视角
水平：88°/垂直：65°(4:3 模式）
最短物体距离
0.5
m
接口
LAN（PoE)
10BASE-T/100BASE-TX，⾃动协商 RJ-45
传感器输⼊
1 端口：闭合触点和断开触点可切换
显示器输出
NTSC/PAL
1.0 Vp-p, 75 欧姆，⾮平衡，负同步
AV 迷你插孔
*
*
在 AV4 端子使用带迷你插头的 AV 电缆。
其他
电源
IEEE802.3af 兼容（PoE 系统）1 级
功率消耗
2.4 W
操作温度
0℃
~
50℃
存放温度
-20℃ 至 +60℃
操作湿度
20% 至 80%（⾮凝结）
存放湿度
20% 至 95%
尺寸（直径 × 长度）
ø
44 mm × 93 mm
质量
约 100 克
随机附件
CD-ROM（用户指南和附带程序）
（1）
传感器输⼊电缆（1）
正面贴片（带标识）
（1）
正面贴片（不带标识）
（1）
使用⼿册（本⽂档）
（1）
设计和规格若有变更，恕不另⾏通知。
定期检查建议
长时间使用本设备时，请定期检查本设备以便安全使用。
虽然设备似乎没有问题，但是长时间使用时其组件质量可能已经下
降，从⽽可能引起故障或事故。
有关详细说明，请咨询购买商店或授权的 Sony 经销商。
