IFV-TR1K.3-859-271-11(1).E
Precautions
On safety
• Unplug the AC power adapter from the AC outlet
when it will not be used for a long period of time. To
disconnect the AC power adapter, pull it out by the
plug. Never pull the cord itself.
• Do not open the cabinet. Refer servicing to qualified
personnel only.
• Be sure that nothing metallic comes into contact with
the metal parts of the AC power adapter. If it does, a
short circuit may occur and the unit may be
damaged.
Operation
• Do not place the units in a location where it is:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Vibrating
• Do not apply mechanical shock or drop the units.
• The units become warm during the use, but this does
not indicate a malfunction.
• Avoid exposing any part of the receiver ’s light
receiver to strong rays such as direct sunlight or
inverter fluorescent lamp rays or to another infrared
ray source such as a remote commander.
• Do not place any obstructions between the
transmitter and receiver, or the visual and sound will
disappear.
• Do not use this system with another infrared ray
transmitter such as cordless headphones or two pairs
of this system at the same time.
The signals may become mixed.
On cleaning and care
• Clean the units with a soft cloth slightly moistened
with water or mild detergent solution.
• Do not use alcohol, benzine or thinner to clean the
units, as they may mar the finish.
Specifications
Transmitter
Video input
Pin jack (1): 1 Vp-p, 75 ohms,
unbalanced, sync negative
Audio input
Pin Jack (2: L, R): –10 dBs,
Input impedance: more than
47 kilohms
Audio output
Stereo mini jack
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature –20°C to 60°C (–4°F to 140°F)
Dimensions
Approx. 95 x 230 x 100 mm (3
3
/
4
x 9
1
/
8
x 4 inches) (w/h/d) (jack
and projected parts not included)
Mass
Approx. 130 g (4.6 oz)
Receiver
Video output
Pin jack (1): 1 Vp-p, 75 ohms,
unbalanced, sync negative (When
POWER is ON)
Audio output
Pin jack (2: L, R): –10 dBs,
Output impedance: less than
10 kilohms (When POWER is
ON)
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature –20°C to 60°C (–4°F to 140°F)
Dimensions
Approx. 95 x 95 x 100 mm (3
3
/
4
x
3
3
/
4
x 4 inches) (w/h/d) (jack
and projected parts not included)
Mass
Approx. 130 g (4.6 oz)
AC power adapter
Input
AC 120 V 60 Hz
Output
DC 9 V 600 mA
Supplied accessories AC power adapter (2)
AV connecting cord (1)
Design and specifications are subject to change without
notice.
Using This System
The following example details the connection of the
transmitter to a camcorder.
Please refer to the operation manual supplied with
your video equipment such as camcorder or video
game.
1
Turn on the camcorder or the video game
connected to the transmitter.
2
Press POWER on the receiver to turn it on
(
O
ON). (See fig.
C
–
a
)
3
Turn the TV on.
4
Set the POWER switch on the transmitter
to ON. (See fig.
C
–
b
)
5
Start the playback by turning on the
camcorder or the video game.
6
Adjust the angle and direction of both the
transmitter and receiver.
Make sure that the infrared receiver and the
transmitter face each other when you use the
system.
Using a headphones (See fig.
C
–
c
)
Connect the headphones to the PHONES jack.
Adjust the volume with the VOL control.
After using this system
Press POWER on the transmitter and the receiver to
turn them off (
o
OFF). The Power lamp goes off.
Coverage of the infrared rays
(See fig.
E
)
The diagrams illustrate the approximate area covered
by the infrared rays. Position the transmitter and the
receiver within the area so that the units operate
effectively.
Notes
• Select the input of the receiver with the input selector on
the TV.
• If the angle of the transmitter or receiver is adjusted past
the movable range as illustrated, it can cause a
malfunction.
• Do not cover the light emitter or receiver of the
transmitter or the receiver with your hand, etc.
• The infrared rays will not penetrate walls or opaque
glass. Therefore, the infrared receiver must be used
within the “in sight” area of the transmitter.
• The brightness of the transmitter ’s light emitter is not
necessarily stabilized. This is not a malfunction and does
not affect the infrared coverage distance.
• Noise and beats appears when the transmitter and the
receiver are positioned too close.
Troubleshooting
If you run into any problem using the system, first
check the power supply source. Then use the following
table for troubleshooting. Should the difficulty persist,
disconnect the power source and contact your Sony
dealer or local authorized Sony service facility.
Trouble
Cause and/or remedy
The AC power adapter is not
connected to the the AC outlet.
n
Connect the AC power adapter
to the AC outlet.
AV connecting cord is not
connected correctly.
n
Connect the AV connecting cord
correctly.
The POWER of the transmitter is
turned off (OFF).
n
Press the POWER button to turn
on the transmitter (ON).
Direct sunlight is shining on the
light receiver of the receiver.
n
Avoid direct sunlight.
The POWER of the receiver is
turned off (OFF).
n
Press the POWER button to turn
on the receiver (ON).
The transmitter and receiver are not
facing each other.
n
Adjust the position and angle of
both units.
The receiver is positioned too far
from the transmitter.
n
Use the transmitter near the
receiver.
The transmitter and receiver are not
facing each other.
n
Adjust the position and angle of
both units.
Another infrared emitting
appliance is operating.
n
Stop operating it.
C
a
b
c
E
No picture and
no sound at all.
The infrared
transmission
system does not
operate.
Background noise
and unclear picture.
Transmitter
Active Speaker
Headphones
to PHONES
Transmitter
: Signal flow
Receiver
Approx. 5 m (16 ft.)
