background image

11

ICF-F11S/F12S

MAIN board

5

1

3

ANT1

not supplied

not supplied

12

14

13

15

1

2

L1

10

11

16

9

6

7

8

4

SECTION  6

EXPLODED  VIEW

  1 

3-254-143-11  SCREW (B3), (+) BV TAPPING

 2 

3-272-871-01 CABINET 

(REAR)

  3 

X-2189-157-1  CABINET FRONT SUB ASSY (including SP1) 

(F11S)

  3 

X-2189-158-1  CABINET FRONT SUB ASSY (including SP1) 

(F12S)

 4 

3-272-874-01 KNOB 

(VOL)

 5 

3-272-873-01 KNOB 

(TUNE)

  6 

3-920-194-11  TERMINAL (–), BATTERY

 7 

3-374-783-02 WASHER, 

POLY-SLIDER

 8 

3-272-878-01 +, 

BATTERY 

TERMINAL

 9 

3-272-875-01 GEAR 

(VC)

 10 

3-044-220-01 HOLDER 

(ANT)

 11 

3-272-880-01 CUSHION 

(SW)

  12 

A-1418-784-A  MAIN BOARD, COMPLETE (F11S)

  12 

A-1418-785-A  MAIN BOARD, COMPLETE (F12S)

 13 

2-580-036-01 CUSHION 

(BATTERY)

  14 

3-272-872-01  LID, BATTERY CASE

  15 

3-918-696-31  SCREW (M3X6 LOCK ACE)

 16 

2-514-259-01 PIN 

(PVC)

 ANT1  1-501-774-31 ANTENNA, 

TELESCOPIC

  L1 

1-457-565-11  BAR ANTENNA COIL (MW)

  Ref. No. 

Part No. 

Description 

Remark

  Ref. No. 

Part No. 

Description 

Remark

Note:

•  -XX and -X mean standardized parts, so 

they may have some difference from the 
original one.

•  Items marked “

*

” are not stocked since 

they are seldom required for routine ser-
vice.

  Some delay should be anticipated when 

ordering these items.

•  The mechanical parts with no reference 

number in the exploded views are not sup-
plied.

•  Color Indication of Appearance Parts Ex-

ample:

  KNOB, BALANCE (WHITE) . . . (RED)
   

 

R

 

R

    

   

 

Parts of Color  Cabinet’s Color

•  Accessories are given in the last of the 

electrical parts list.

Summary of Contents for ICF-F11S





















Reviews: