Sony HXR-NX5R Operating Manual Download Page 115

Page: 115 / 148

115

rou
bl

oot
in

The remaining battery indicator does not indicate the correct figure.

• Ambient temperature is too high or too low, or the battery pack has not been charged enough.

This is not a malfunction.

• Fully charge the battery again. If the problem persists, the battery may be worn-out. Replace

with a new battery (p. 19, 134).

• The indicated figure may not be correct in certain circumstances. For example, when you

open or close the LCD screen, it takes about 1 minute to display the correct remaining
battery.

The battery pack discharges too quickly.

• Ambient temperature is too high or too low, or the battery pack has not been charged enough.

This is not a malfunction.

• Fully charge the battery again. If the problem persists, the battery may be worn-out. Replace

with a new battery (p. 19, 134).

The image on the viewfinder is not clear.

• Move the diopter adjustment dial until the image is clear (p. 27).

The viewfinder image is not displayed.

• Press the VF/LCD PANEL button (p. 28).

The supplied Wireless Remote Commander does not function.

• Set [REMOTE CONTROL] to [ON] (p. 106).
• Remove any obstructions between the Wireless Remote Commander and the remote sensor

of the camcorder.

• Keep strong light sources, such as sunlight or overhead lighting, away from the remote

sensor, otherwise the Wireless Remote Commander may not function properly.

• Change the battery. Insert a fresh battery with the +/– terminals aligned correctly (p. 14).

Another video device malfunctions when you use the supplied Wireless
Remote Commander.

• Select a commander mode other than DVD2 for your video device.
• Cover the sensor of your video device with black paper.

The camcorder does not operate normally when a device is connected to the
REMOTE jack.

• The speed in response to commands from the Wireless Remote Commander may be slow.
• The camcorder settings may not be restored if a cable is connected to the REMOTE jack of

the camcorder and the device on the other end of the cable is disconnected. Disconnect the
cable from the camcorder’s REMOTE jack.

Continued

Summary of Contents for HXR-NX5R





















































































































































Search results

Summary of Contents for HXR-NX5R

Reviews:

Sony HXR-NX5R, Operating Manual, Page: 115 / 148

Search results

Summary of Contents for HXR-NX5R

Reviews: