Sony HXCU-FB80 Service Manual Download Page 9 | Manualshive

Page: 9 / 102

Sony HXCU-FB80 Service Manual Download Page 9

Manual Structure

Purpose of this manual

This manual is intended for the use of the system engineers and the service engineers, and provides the limited
information for block service and the information related to maintenance of the unit, service overview, periodic
maintenance and inspection, replacement of main parts, electrical alignment, software update, maintenance mode, circuit
description, spare parts, block diagram, frame wiring, and etc. .

Related manuals

The following manuals are available for this model.
If any of these manuals is required, please contact your local Sony Sales Office/Service Center.

• Operating Instructions CD-ROM (supplied with the unit)

This manual contains information required to operate and use the unit.

• Installation Manual (available on request)

This manual provides the information on installing the unit.

• Factory Service Manual (available on request)

This manual provides the limited information for component service and the information related to maintenance
of the unit.

Trademarks

Trademarks and registered trademarks described in this manual are as follows.

• FRAM is a registered trademark of Ramtron International Corporation.

Other system names and product names written in this manual are usually registered trademarks or trademarks of
respective development manufacturers.

HXCU-FB80

5

«
...
7
8
9
10
11
...
»

Summary of Contents for HXCU-FB80







































































































Reviews:

No comments