Sony HT-BE1, Service Manual

Page: 11 / 56

11 11
HT-BE1/SA-WBE1/SS-BE1
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1 /
4
W or less unless otherwise
specified.
•
2
: nonflammable resistor.
•
C
: panel designation.
Note:
The components identi-
fied by mark
0 or dotted
line with mark
0
are criti-
cal for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque
0
sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
• A : B+ Line.
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
• Voltages are taken with a VOM (Input impedance 10 M Ω ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Signal path.
F
: LINE
c : DIGITAL AUDIO (OPTICAL)
J : DIGITAL AUDIO (COAXIAL)
• Abbreviation
CND : Canadian model.
SP
: Singapore model.
MY : Malaysia model.
MX : Mexican model.
• ( ) : Page of Service Manual.
(( )) : Page of Supplement-1.
Note on Printed Wiring Boards:
•
X
: parts extracted from the component side.
•
: Pattern from the side which enables seeing.
• Abbreviation
CND : Canadian model.
SP
: Singapore model.
MY : Malaysia model.
MX : Mexican model.
• ( ) : Page of Service Manual.
(( )) : Page of Supplement-1.
55 BTACT O Not used. (open)
56 BST I Boot stop signal input from system controller.
57 MOD1 I Operation mode signal input (Fixed at H : 256fs)
58 MOD0 I Operation mode signal input (Fixed at L : single chip mode)
59 EXLOCK I Lock signal input
60 VDDI I Power supply pin (+2.4 V)
61 VSS — Ground
62 to 66 A17 to A13 O External memory address output (SRAM) (Not used. (open))
67 GP10 O Connected to LRCKO
68 GP9 O Decode signal output for system controller.
69 GP8 I Audio signal input from DIR.
70 VDDI I Power supply pin (+2.4 V)
71 VSS — Ground
72 to 75 D15/GP7 to D12/GP4 I/O External memory data input/output (general port) (Not used. (open))
76 VDDE I Power supply pin (+3.3 V)
77 to 80 D11/GP3 to D8/GP0 I/O External memory data input/output (general port) (Not used. (open))
81 VSS — Ground
82 A9 O External memory address output (SRAM) (Not used. (open))
83 to 85 A12 to A10 O External memory address output (SRAM) (Not used. (open))
86 TDO O Not used. (open)
87 TMS I Not used. (open)
88 XTRST I Not used. (open)
89 TCK I Not used. (open)
90 TDI I Not used. (open)
91 VSS — Ground
92 to 97 A8 to A3 O External memory address output (SRAM) (Not used. (open))
98, 99 D7, D6 I/O External memory data input/output (SRAM) (Not used. (open))
100 VDDI I Power supply pin (+2.4 V)
101 VSS — Ground
102 to 105 D5 to D2 I/O External memory data input/output (SRAM) (Not used. (open))
106 VDDE I Power supply pin (+3.3 V)
107, 108 D1, D0 I/O External memory data input/output (SRAM) (Not used. (open))
109, 110 A2, A1 O External memory address output (SRAM) (Not used. (open))
111 VSS — Ground
112 A0 O External memory address output (SRAM) (Not used. (open))
113 PM I PLL initialization input from system controller.
114, 115 SDI3, SDI4 I Not used. (open)
116 SYNC I Sync/async selection input (Fixed at H : async)
117 to 119 VSS — Ground
120 VDDI I Power supply pin (+2.4 V)
Pin No. Pin Name I/O Pin Description
• Waveforms
1
IC501 wk (XT0)
1V/div 50nsec/div
12.0MHz
2
IC803 wa (XOUT)
1V/div 50nsec/div
12.288MHz
3
IC801 ek (X2)
1V/div 20nsec/div
4
IC802 qs (MCLK2)
1V/div 50nsec/div
16.0MHz
13.5MHz
5
IC802 qf (SCKOUT)
1V/div 50nsec/div
13.5MHz
3.0Vp-p
3.5Vp-p
2.6Vp-p
3.1Vp-p
4.0Vp-p
Ver. 1.3