– 89 –
• IC121 Digital Signa; Processor, Digitak Servo Signal Processor, EFM/ACIRC Encoder/Decoder, Shock-proof Memory
Controller, ATRAC Encoder/Decoder, 2M Bit DRAM (CXD2652R) (BD (MD) Board)
1
MNT0 (FOK)
O
2
MNT1 (SHCK)
O
Track jump detection signal output to the MD system controller (IC316)
3
MNT2 (XBUSY)
O
Monitor 2 signal output to the MD system controller (IC316)
4
MNT3 (SLOC)
O
Monitor 3 signal output to the MD system controller (IC316)
5
SWDT
I
Writing data signal input from the MD system controller (IC316)
6
SCLK
I
Serial clock signal input from the MD system controller (IC316)
7
XLAT
I
Serial latch signal input from the MD system controller (IC316)
8
SRDT
O (3)
Reading data signal output to the MD system controller (IC316)
9
SENS
O (3)
Internal status (SENSE) output to the MD system controller (IC316)
10
XRST
I
Reset signal input from the MD system controller (IC316)
“L”: reset
11
SQSY
O
12
DQSY
O
13
RECP
I
14
XINT
O
Interrupt status output to the MD system controller (IC316)
15
TX
I
16
OSCI
I
System clock signal (512Fs=22.5792 MHz) input terminal
17
OSCO
O
System clock signal (512Fs=22.5792 MHz) output terminal
18
XTSL
I
19
RVDD
—
Power supply terminal (+3.3V) (digital system)
20
RVSS
—
Ground terminal (digital system)
21
DIN
I
Digital audio signal input terminal when recording mode (for optical in)
22
DOUT
O
Digital audio signal output terminal when playback mode (for optical out)
Not used
23
ADDT
I
Recording data input from the A/D, D/A converter (IC201)
24
DADT
O
Playback data output to the A/D, D/A converter (IC201)
25
LRCK
O
L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC201)
26
XBCK
O
Bit clock signal (2.8224 MHz) output to the A/D, D/A converter (IC201)
27
FS256
O
Clock signal (11.2896 MHz) output to the A/D, D/A converter (IC201)
28
DVDD
—
Power supply terminal (+3.3V) (digital system)
29
A03
O
30
A02
O
31
A01
O
32
A00
O
33
A10
O
34
A04
O
Address signal output to the external D-RAM (IC124)
35
A05
O
36
A06
O
37
A07
O
38
A08
O
39
A11
O
* I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.
Pin No.
Pin Name
I/O
Function
Focus OK signal output to the MD system controller (IC316)
“H” is output when focus is on
Subcode Q sync (SCOR) output to the MD system controller (IC316)
“L” is output every 13.3 msec
Almost all, “H” is output
Digital In U-bit CD format subcode Q sync (SCOR) output to the MD system controller
(IC316)
“L” is output every 13.3 msec Almost all, “H” is output
Laser power selection signal input from the MD system controller (IC316)
“H”: recording mode, “L”: playback mode
Recording data output enable signal input from the MD system controller (IC316)
Writing data transmission timing input (Also serves as the magnetic head on/off output)
Input terminal for the system clock frequency setting
“L”: 45.1584 MHz, “H”: 22.5792
MHz (fixed at “H” in this set)
Summary of Contents for HCD-MD333 - Hi Fi Cd/minidisc Component
