Sony Handycam CCD-TR57 Page 66 Operating Instructions Manual Download

Page: 66 / 80

Symptom

Cause and/or Corrective Actions

• The battery pack is not installed.

Install the battery pack. (p. 7)

• The battery is dead.

Use a charged battery pack. (p. 8)

• The AC power adaptor is not connected to a wall outlet.

Connect the AC power adaptor to a wall outlet. (p. 23)

• While being operated in CAMERA mode, the camcorder

has been in Standby mode for more than 5 minutes.

Turn STANDBY down once and then up again. (p. 12)

• The battery is dead.

Use a charged battery pack. (p. 8)

• The camcorder does not operate when using a battery

pack that is not an “InfoLITHIUM” battery pack.

Use an “InfoLITHIUM” battery pack. (p. 61)

• The ambient temperature is too low. (p. 59)
• The battery pack has not been charged fully.

Charge the battery pack again. (p. 8)

• The battery pack is completely dead, and cannot be

recharged.

Use another battery pack. (p. 60)

• The AC power adaptor is disconnected.

Connect it firmly.

• Something is wrong with the battery pack.

Contact your Sony dealer or local authorized Sony
service facility.

If you run into any problem using the camcorder, use the following table to
troubleshoot the problem. Should the difficulty persist, disconnect the power source
and contact your Sony dealer or local authorized Sony service facility.

Camcorder

Power

Trouble check

The battery pack is quickly
discharged.

The power goes off.

The power is not on.

While charging the battery pack, no
indicator appears or the indicator
flashes in the display window.

Summary of Contents for Handycam CCD-TR57

















































































Search results

Summary of Contents for Handycam CCD-TR57

Reviews:

Related manuals for Handycam CCD-TR57

Brands by name

Popular brands

Sony Handycam CCD-TR57, Operating Instructions Manual

Search results

Summary of Contents for Handycam CCD-TR57

Reviews:

Related manuals for Handycam CCD-TR57

Brands by name

Popular brands