Sony DVP-S7700, Operating Instructions Manual

Page: 40 / 108

Settings and Adjustments
40 GB
Settings for Output Signal
Format (INITIAL SETUP 3)
Select “
3
” after pressing SET UP.
“INITIAL SETUP 3” allows you to control the output
signal format from the player via the EURO AV and
DIGITAL OUT OPTICAL and COAXIAL connectors.
Default settings are underlined.
Notes
• When you set “EURO AV OUT” to “RGB”, you cannot set
“COMPONENT OUT” to “ON”, and vice versa.
• When you set “DIGITAL OUT“ to “OFF”, you cannot select
“DOLBY DIGITAL”, “MPEG”, and “DTS.“
p COMPONENT OUT
Selects the methods of outputting video signals from the
COMPONENT VIDEO OUT (Y, C
B
/B-Y, C
R
/R-Y) connectors
on the rear panel of the player.
• ON: outputs the component video signals.
• OFF: outputs no signals.
Notes
• When you set “EURO AV OUT” to “RGB”, you cannot set
“COMPONENT OUT” to “ON.”
• When you connect the player to a monitor or projector via
only the COMPONENT VIDEO OUT connectors, do not
select “OFF.” If you select “OFF” in this case, the picture
may not appear.
p EURO AV OUT
Selects the methods of outputting video signals from the
EURO AV 1(RGB)–TV connectors on the rear panel of the
player.
• VIDEO: outputs the video signals.
• S VIDEO: outputs the S video signals.
• RGB: outputs the RGB signals.
Notes
• When you set “COMPONENT OUT” to “ON”, you cannot
set “EURO AV OUT” to “RGB.”
• If your TV is not conformed to the S video or the RGB
signals, no picture appears on the TV screen even if you
select “S VIDEO” or “RGB.” Refer to the instructions
supplied with your TV.
• If your TV has only one EURO AV IN connector, do not
select “S VIDEO.”
p DIGITAL OUT
Selects output signals via the DIGITAL OUT OPTICAL and
COAXIAL connectors.
• ON: Normally select this position.
• OFF : when the player does not output the sound signals
via DIGITAL OUT OPTICAL and COAXIAL connectors, if
you select this position, the influence of the digital circuit
upon the analog one becomes minimum.
p DOLBY DIGITAL
Selects output Dolby Digital (AC-3) signals via the DIGITAL
OUT OPTICAL and COAXIAL connectors. You cannot select
this item when you set “DIGITAL OUT” to “OFF.”
• D-PCM (Downmix PCM): when you play the Dolby Digital
(AC-3) sound tracks, the output audio signals are mixed
down to 2 channels. By the settings of the item
“SURROUND” in “INITIAL SETUP 2”, you can select
whether the signals conform to Dolby surround, Dolby Pro
Logic surround, etc., or not.
• DOLBY DIGITAL: when the player is connected to an
audio component with a built-in Dolby Digital (AC-3)
decoder.
Note
If the player is connected to an audio component without a
built-in Dolby Digital (AC-3) decoder, do not set “DOLBY
DIGITAL” in “INITIAL SETUP 3” to “DOLBY DIGITAL.”
Otherwise, when you play the Dolby Digital (AC-3) sound
track, a loud noise or no sound will come out from the
speakers, affecting your ears or causing the speakers to be
damaged.
p
MPEG
Selects output MPEG AUDIO signals via the DIGITAL OUT
OPTICAL and COAXIAL connectors. You cannot select this
item when you set “DIGITAL OUT” to “OFF.”
• PCM: when the player is connected to an audio component
without a built-in MPEG decoder. If you play MPEG
AUDIO sound tracks, the player outputs stereo signals
taken from MPEG AUDIO signals via the DIGITAL OUT
OPTICAL and COAXIAL connectors.
• MPEG: when the player is connected to an audio
component with a built-in MPEG decoder.
Note
If the player is connected to an audio component without a
built-in MPEG decoder, do not set “MPEG” in “INITIAL
SETUP 3” to “MPEG.” Otherwise, when you play the MPEG
AUDIO sound track, a loud noise will come out from the
speakers, affecting your ears or causing the speakers to be
damaged.
I N I T I A L S E T U P 3
D I G I T A L O U T :
M P E G : P C M
D - P C M
D T S : O F F
Q U I T
ENTER SETUP
D O L B Y D I G I T A L :
O N
1 2 3
E U R O A V O U T V I D E O
C O M P O N E N T O U T
O N