background image

1

Ver 1.1  2004. 05

Model Name Using Similar Mechanism

CDX-R3000/RW300

CD Drive Mechanism Type

MG-611XA-186//K

Optical Pick-up Name

KSS1000E

SERVICE MANUAL

US Model

CDX-F5000/FW500

Canadian Model

CDX-F5000

CDX-F5000/FW500

AUDIO POWER SPECIFICATIONS

POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.

CD player section

Signal-to-noise ratio

120 dB

Frequency response

10 – 20,000 Hz

Wow and flutter

Below measurable limit

Tuner section

FM

Tuning range

87.5 – 107.9 MHz

Antenna terminal

External antenna connector

Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity

9 dBf

Selectivity

75 dB at 400 kHz

Signal-to-noise ratio

67 dB (stereo),
69 dB (mono)

Harmonic distortion at 1 kHz

0.5% (stereo),
0.3% (mono)

Separation

35 dB at 1 kHz

Frequency response

30 – 15,000 Hz

AM

Tuning range

530 – 1,710 kHz

Antenna terminal

External antenna connector

Intermediate frequency 10.7 MHz/450 kHz
Sensitivity

30 

µ

V

Power amplifier section

Outputs

Speaker outputs
(sure seal connectors)

Speaker impedance

4 – 8 ohms

Maximum power output 52 W 

×

 4 (at 4 ohms)

SPECIFICATIONS

General

Outputs

Audio outputs terminal (rear/sub switchable)
Power antenna relay control terminal
Power amplifier control terminal

Inputs

Telephone ATT control terminal
Remote controller input terminal
BUS control input terminal
BUS audio input terminal
Antenna input terminal

Tone controls

Low: 

±

10 dB at 60 Hz (XPLOD)

Mid: 

±

10 dB at 1 kHz (XPLOD)

High: 

±

10 dB at 10 kHz (XPLOD)

Power requirements

12 V DC car battery
(negative ground)

Dimensions

Approx. 178 

×

 50 

×

 177 mm

(7 

1/8

 

×

 2 

×

 7 in.) (w/h/d)

Mounting dimensions

Approx. 182 

×

 53 

×

 161 mm

(7 

1/4

 

×

 2 

1/8

 

×

 6 

3/8

 

in.) (w/h/d)

Mass

Approx. 1.2 kg
(2 lb. 10 oz.)

Supplied accessories

Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander RM-X115

Design and specifications are subject to change without
notice.

• The tuner and CD sections have no adjustments.

Sony Corporation

e Vehicle Company

Published by Sony Engineering Corporation

9-961-429-02

2004E04-1

© 2004. 05

FM/AM COMPACT DISC PLAYER

Summary of Contents for CDX-F5000 - Fm/am Compact Disc Player













































Reviews: