Sony CDX-3170 Page 37 Service Manual Download

Page: 37 / 44

– 45 –

SECTION 6

ELECTRICAL PARTS LIST

NOTE:

• Due to standardization, replacements in

the par ts list ma y be diff erent fr om the
par ts specified in the dia

grams or the

components used on the set.

• -XX and -X mean standardized parts, so

the y ma y ha ve some diff erence fr om the
original one.

• RESIST ORS

All resistors are in ohms.
METAL:Metal-film resistor

METAL OXIDE: Metal o xide-film resistor

F:nonflammable

• Items marked “*” are not stoc

ked since

the y are seldom required f

or r outine ser vice .

Some delay should be anticipated
when ordering these items.

• SEMICONDUCT ORS

In eac h case , u :

, for e xample:

uA..

A..

uPA.. :

PA..

uPB.. :

PB.. uPC.. :

PC.. uPD.. :

PD..

• CAPACITORS

uF :

• COILS

uH :

Ref. No.

Part No.

Description

Remark

Ref. No.

Part No.

Description

Remark

The components identified b

mark

or dotted line with mark.

are critical f or saf ety .

Replace only with part number
specified.

When indicating parts by reference
number , please inc lude the boar

DISPLAY

DISC IN SW

1-659-836-11 DISC IN SW BOARD

****************

< SWITCH >

SW1

1-572-288-11 SWITCH, PUSH (DISC IN)

SW2

1-572-288-11 SWITCH, PUSH (SELF)

*************************************************************

DISPLAY BOARD

**************

3-009-335-02 PLATE (LCD), LIGHT GUIDE

3-009-337-01 HOLDER (LCD)

3-009-341-01 SHEET (LCD)

3-009-371-01 BRACKET (PCB)

3-014-202-01 BRACKET (LCD)

< CAPACITOR >

C851

1-163-137-00 CERAMIC CHIP

680PF

50V

C852

1-163-038-11 CERAMIC CHIP

0.1uF

25V

C853

1-163-117-00 CERAMIC CHIP

100PF

50V

< CONNECTOR >

CNP801 1-764-423-11 PIN, CONNECTOR 12P

CNP802 1-779-129-11 PIN, CONNECTOR 3P

< DIODE >

D851

8-719-976-99 DIODE DTZ5.1B

D852

8-719-052-61 LED SLR-342PGA47 (SENS)

D853

8-719-052-61 LED SLR-342PGA47 (

)

D854

8-719-052-61 LED SLR-342PGA47 (A.MEM)

D855

8-719-052-61 LED SLR-342PGA47 (6)

D856

8-719-052-61 LED SLR-342PGA47 (2/REPEAT)

D857

8-719-052-61 LED SLR-342PGA47 (3/SHUF)

D858

8-719-052-61 LED SLR-342PGA47 (4)

D859

8-719-064-19 LED SLR-342PG (5)

D860

8-719-052-61 LED SLR-342PGA47 (SEL)

D861

8-719-052-61 LED SLR-342PGA47 (MODE)

D862

8-719-052-61 LED SLR-342PGA47 (SOURCE)

D863

8-719-052-61 LED SLR-342PGA47 (+)

D864

8-719-052-61 LED SLR-342PGA47 (ATT)

D865

8-719-052-61 LED SLR-342PGA47 (-)

D868

8-719-052-61 LED SLR-342PGA47 (DSPL)

D869

8-719-052-61 LED SLR-342PGA47 (OFF)

D870

8-719-052-61 LED SLR-342PGA47 (1/INTRO)

D872

8-719-105-99 DIODE RD6.2M-B1

D873

8-719-105-99 DIODE RD6.2M-B1

D874

8-719-105-99 DIODE RD6.2M-B1

D875

8-719-105-99 DIODE RD6.2M-B1

< IC >

IC801

8-759-369-90 IC LC75822ED

< JUMPER RESISTOR >

JR802

1-216-295-00 SHORT

JR804

1-216-296-00 SHORT

JR805

1-216-296-00 SHORT

JR806

1-216-296-00 SHORT

JR807

1-216-296-00 SHORT

JR808

1-216-296-00 SHORT

JR809

1-216-296-00 SHORT

JR810

1-216-296-00 SHORT

JR811

1-216-296-00 SHORT

JR812

1-216-296-00 SHORT

JR816

1-216-295-00 SHORT

JR817

1-216-295-00 SHORT

JR818

1-216-295-00 SHORT

< LIQUID CRYSTAL DISPLAY >

LCD800 1-803-140-11 DISPLAY PANEL, LIQUID CRYSTAL

< PILOT LAMP >

PL801

1-517-677-11 LAMP, PILOT

PL802

1-517-677-11 LAMP, PILOT

< RESISTOR >

R841

1-216-193-00 RES,CHIP

620

1/8W

R842

1-216-193-00 RES,CHIP

620

1/8W

R851

1-216-090-00 METAL CHIP

51K

1/10W

R852

1-216-049-11 RES,CHIP

1/10W

R854

1-247-808-11 CARBON

110

1/4W

R855

1-247-808-11 CARBON

110

1/4W

R856

1-247-818-11 CARBON

300

1/4W

R857

1-247-818-11 CARBON

300

1/4W

R859

1-247-818-11 CARBON

300

1/4W

R860

1-247-822-11 CARBON

430

1/4W

R861

1-216-053-00 METAL CHIP

1.5K

1/10W

R862

1-216-057-00 METAL CHIP

2.2K

1/10W

R863

1-247-843-11 CARBON

3.3K

1/4W

R864

1-216-067-00 METAL CHIP

5.6K

1/10W

Summary of Contents for CDX-3170













































Search results

Summary of Contents for CDX-3170

Reviews:

Related manuals for CDX-3170

Brands by name

Popular brands

Sony CDX-3170, Service Manual

Search results

Summary of Contents for CDX-3170

Reviews:

Related manuals for CDX-3170

Brands by name

Popular brands