Sony CDC-X217 Operating Instructions Manual Download Page 8

SPECIFICATIONS

RADIO SECTION

(FM)

Frequency Range: 87.5 MHz – 108 MHz (100-kHz
steps)* or 87.5 MHz – 108 MHz (50-kHz steps)*
Usable Sensitivity: 12.7 dBf
50 dB Quieting Sensitivity: 17.2 dBf
IF Rejection: 80 dB
Frequency Response: 30 Hz – 15,000 Hz
S/N Ratio: 63 dB
Stereo Separation: 35 dB at 1 kHz
Alternate Channel Selectivity: 70 dB
Capture Ratio: 3 dB

(AM)

Frequency Range: 530 kHz – 1,710 kHz (10-kHz
steps)* or 531 kHz – 1,602 kHz (9-kHz steps)*
Usable Sensitivity: 30 µV (30 dB)

* Set the frequency increment for your area using

the switch on the bottom of the unit. (The switch
is factory-set to the 10k position [for the U.S.A.])

CD SECTION

Frequency Response: 17 Hz – 20 kHz +0/–3 dB
Dynamic Range: More than 80 dB
Channel Separation: More than 65 dB
S/N Ratio: More than 85 dB
Wow/Flutter: Not applicable

AUDIO SECTION

Max. Power Output: 45 W 

×

 4 channels

AUX IN input

Input sensitivity (load impedance) AUX IN: 300 mV
(10 k

)

GENERAL

Power-Supply Voltage: 14.4 V (11 to 16 V
allowable), DC, negative ground
Load Impedance: 4 

Tone Control:
Bass ± 10 dB at 100 Hz, Treble ± 10 dB at 10 kHz
Preamp Output Voltage (load impedance): 2.2 V
(10 k

)

Installed size: 182 (W) 

×

 53 (H) 

×

 155 (D) mm

(7 

1

/

4

 (W) 

×

 2 

1

/

8

 (H) 

×

 6 

1

/

8

 (D) inches)

Supplied Accessory: Carrying case (1)

• Specifications and external appearance are subject to

change without notice due to product improvement.

7

  ENGLISH

REAR PANEL

Summary of Contents for CDC-X217











Reviews: