background image

1-6(E)

AMS-100

1-8. Input Level Meter Adjustment

Preparation

.

Input the reference signal to the unit:

When the BKAM-101 is attached : 

+

4 dBm

When the BKAM-102 is attached : 

_

20 dB FS

.

Turn on the power of the unit and select the slot and the

channel to which the reference signal is to be input on

the INPUT SELECT operation panel.

(For details on operation, refer to the Operation Manual.)

.

Let the unit warm up for about 10 minutes.

Adjustment procedures

1.

Press and hold the button corresponding to the desired

slot for 3 seconds or more on the INPUT SELECT

operation panel to enter Adjustment mode.

2.

Check that the LED for the channel you are selecting

starts blinking.

3.

Perform the following adjustment.

Adj. point :

Adjustment screw L/input level meter

Adjustment screw R/input level meter

Specification : The LEDs for “0” level start blinking.

Setting after adjustment

To return from Adjustment mode, press any button on the

INPUT SELECT operation panel.

1-9. Related manuals

Besides this Installation Manual, the following manuals are

available for the AMS-100.

.

Operation Manual (Supplied with the AMS-100)

This manual explains the overview of the AMS-100, and

the system configuration examples.

.

Maintenance Manual (available on request)

This manual describes information that premise the

service based on parts replacement (adjustments, board

layouts, schematic diagrams, parts list, etc.).

If this manual is required, contact your local Sony Sales

Office/Service Center.

1-8. Adjustment of the Input Level Meter
1-9. Related manuals

+

3

+

1
0

_

1

_

3

_

5

_

7

_

10

_

15

_

20

+

3

+

1
0

_

1

_

3

_

5

_

7

_

10

_

15

_

20

L

R

LEDs for "0" level

Adjustment screws

Summary of Contents for AMS-100











Reviews: