Sony Ericsson XPERIA X10 Mini Pro U20a Troubleshooting Manual Download Page 46

Page: 46 / 47

Trouble Shooting (mech)

1233-9027 Rev2

Sony Ericsson Mobile Communications AB – Company Internal

46(47)

Problem Areas: Sensors

Check:

Inspect the PBA H2H Flex.

Action:

1. If the PBA H2H Flex or its ZIF connector is damaged –
replace the PBA H2H Flex.

2. Send to higher level of repair.

1.29.2 Slide Sensor

Check:

Inspect the magnet on the Hinge assembly.

Action:

1. If dirty – clean it.

2. If not properly positioned – reinstall it.

3. If the magnet is missing or damaged – replace the Hinge
assembly.

Check:

Inspect the Slider Sensor IC on the PBA Dome, Complete.

Action:

1. If damaged – replace the PBA Dome, Complete.

2. Send to higher level of repair.

Summary of Contents for XPERIA X10 Mini Pro U20a
















































Search results

Summary of Contents for XPERIA X10 Mini Pro U20a

Reviews:

Related manuals for XPERIA X10 Mini Pro U20a

Brands by name

Popular brands

Sony Ericsson XPERIA X10 Mini Pro U20a, Troubleshooting Manual

Search results

Summary of Contents for XPERIA X10 Mini Pro U20a

Reviews:

Related manuals for XPERIA X10 Mini Pro U20a

Brands by name

Popular brands