Sonoma SGR27 Instructions Manual Download Page 8 | Manualshive

Page: 8 / 8

Sonoma SGR27 Instructions Manual Download Page 8

6. Install the NG valve assembly to the under side

of the side burner with the two (2) screws
previously removed. (See Fig. 33).

Note: Make sure the NG valve is facing towards

the front of the side burner and the valve
stem is inserted into the hole.

7. Reattach the bezel to the front of the side burner

and the NG valve with the two (2) screws
previously removed. (See Fig. 34).

Note: Make sure the bezel is installed in the

correct position. The “H” will be facing the
igniter.

8. Reattach the control knob.

9. Carefully run the supplied hose from the inside of

the cart through the grommeted hole in the cart
to the side burner assembly.

10. Connect the end of the new gas supply hose to

the NG valve assembly. (See Fig. 35).

This completes the side burner conversion.

Note: At the completion of the conversion, a leak

test should be performed on all fittings.
See Use and Care manual for leak testing
procedure.

Installation is now complete.

Enjoy your grill safely.

8

SGR27 Natural Gas Conversion Instructions

51053001
2/16/06

Fig 33

Screw

Fig 34

Screws

Bezel

Fig 35

Underside of side

burner shelf

“H”

«
...
6
7
8

Summary of Contents for SGR27









Reviews:

No comments