SONIX SN32F280 Series User Manual Download | Manualshive

Page: 179 / 268

background image

SN32F280 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 179

Version 1.1

0: Auto-baud has not finished.

1: Auto-baud has finished successfully and interrupt is enabled.

7:4

Reserved

R

0100b

3:1

INTID[2:0]

Interrupt identification which identifies an interrupt corresponding to the

USARTn RX FIFO.

0x3: 1 - Receive Line Status (RLS).

0x2: 2a - Receive Data Available (RDA).

0x1: 3a - THRE Interrupt.

0x7: 3b

– TEMT Interrupt.

Other: Reserved

R

0

0

INTSTATUS

Interrupt status. The pending interrupt can be determined by evaluating

USARTn_II[3:1].

0: At least one interrupt is pending.

1: No interrupt is pending.

R

1

Bits UARTn_II[9:8] are set by the auto-baud function and signal a time-out or end of auto-baud condition. The auto-baud
interrupt conditions are cleared by setting the corresponding Clear bits in the Auto-baud Control Register.

Given the status of UARTn_II[3:0], an interrupt handler routine can determine the cause of the interrupt and how to clear
the active interrupt. The UARTn_II register must be read in order to clear the interrupt prior to exiting the Interrupt
service routine.

Interrupt USARTn_II

[3:0]

Priority

Interrupt Source

Interrupt Reset

RLS

0110

Highest

Overrun error (OE)

,

Parity error (PE),

Framing error (FE)

or Break interrupt (BI)

Read UARTn_LS register

RDA

0100

2

nd

RX data in FIFO reached trigger level (FCR0=1)

Read UARTn_RB register
or UART FIFO drops
below trigger level

THRE

0010

3

rd

THRE

Read UARTn_II register
(if source of interrupt) or
Write THR register

TEMT

1110

3

rd

TEMT

Read UARTn_II register
(if source of interrupt) or
Write THR register

15.7.7 UART n Line Control register (UARTn_LC) (n=0,1,2,3)

Address Offset: 0x0C

This register determines the format of the data character that is to be transmitted or received.

Bit

Name

Description

Attribute

Reset

31:8

Reserved

R

0

7

DLAB

Divisor Latch Access bit
0: Disable access to Divisor Latches.
1: Enable access to Divisor Latches.

R/W

0

6

BC

Break Control bit
0: Disable break transmission.
1: Enable break transmission. Output pin UART TXD is forced to logic 0.

R/W

0

5:4

PS[1:0]

Parity Select bits
00: Odd parity. Number of 1s in the transmitted character and the attached

parity bit will be odd.

01: Even Parity. Number of 1s in the transmitted character and the

attached parity bit will be even.

10: Forced 1 stick parity.
11: Forced 0 stick parity.

R/W

0

3

PE

Parity Enable bit

R/W

0

«
...
177
178
179
180
181
...
»

Summary of Contents for SN32F280 Series













































































































































































































































































Reviews:

No comments

Related manuals for SN32F280 Series

Brand: Gardena Pages: 17

Brand: Badger Meter Pages: 16

MorphoAccess SIGMA Extreme Series

Brand: Safran Pages: 79

Brand: Lawler Pages: 5

Brand: NCR Pages: 8

Brand: L-Acoustics Pages: 24

Brand: L-Acoustics Pages: 21

Brand: Rain Bird Pages: 18

Brand: BQT Pages: 2

Brand: Harman Pages: 2

Brand: Linear Technology Pages: 6

Brand: Carrier Pages: 4

Brand: Vexve Pages: 24

Brand: KELCO Pages: 4

Brand: Melexis Pages: 13

Brand: DROPSA Pages: 29

Brand: Qorvo Pages: 45

Brand: KELD Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands