SONIX SN32F280 Series User Manual Download Page 16

Page: 16 / 268

SN32F280 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 16

Version 1.1

PRODUCT OVERVIEW

1.1 FEATURES



Memory configuration



Timer

128KB on-chip Flash programming memory.

3 16-bit timer support up-counting, down-counting, and

32KB SRAM.

center-aligned mode.

4KB Boot ROM

3 16-bit timers support up-counting mode.

28 sets PWM



Operation Frequency up to 48MHz

8 sets inverse PWM with programmable dead-band

PCLK up to 96MHz



Interrupt sources

ARM Cortex-M0 built-in Nested Vectored Interrupt



Working voltage 2.5V ~ 5.5V

Controller (NVIC).



12-bit SAR ADC with 12 external and 3 internal



I/O pin configuration

channels, and 4-level Int. Ref. Voltage

Up to 74 General Purpose I/O (GPIO) pins with

16 external ADC input

configurable pull-up resistors.

1 internal battery measurement

GPIO pins can be used as edge and level sensitive

2 internal channels from OPA0 and OPA1 outputs.

interrupt sources.

4-level internal reference voltage source (VDD, 4.5V,

Up to 6 High-current (100 mA) output sink pins: P0.0,

3V, 2V)

P0.1, P0.2, P0.3, P1.12, P1.13

All IO 20mA driving/sinking current



3 Rail to Rail Comparators

4 GPIO pins with configurable pull-down resistors:

Internal reference voltage source 3V/2V/1.5V

P3.10, P3.11, P3.12, P3.13

Programmable 16-level internal ref. voltage divider

3 external negative inputs



Programmable Watchdog Timer (WDT)

3 external positive inputs

Programmable watchdog frequency with watchdog

clock source and divider.



2 OPA

Internal reference voltage source 3V/2V/1.5V shared



System tick timer

with CMP

The 24-bit SysTick timer clock source is fixed to the

system clock, and is intended to generate a fixed 10-



Interface

ms interrupt.

-Two I2C controllers supporting I2C-bus specification

with multiple address recognition.



Real-Time Clock (RTC)

-Four UART controllers with fractional baud rate

generation.



LVD with separate thresholds

-Two SPI controllers.

Reset: 1.35V for V

CORE

1.5V

- EBI (8080 included) interface

Reset: 2.7V/3.0V/3.6V for VDD

- Two I2S controllers with mono and stereo audio data

Interrupt: 2.7V/3.0V/3.6V for VDD

supported, MSB justified data format supported, and

can operate as either master or slave.



Fcpu (Instruction cycle)

CPU

= F

HCLK

= F

SYSCLK

/1, F

SYSCLK

/2, F

SYSCLK

/4, …,



System clocks

SYSCLK

/128

-External high clock: Crystal type 10MHz~25MHz

-External low clock: Crystal type 32.768 KHz



Operating modes

-Internal high clock: RC type 12 MHz

Normal, Sleep, Deep-sleep

-Internal low clock: RC type 32 KHz

-PLL allows CPU operation up to the maximum CPU



Cyclic Redundancy Check (CRC)

rate without the need for a high-frequency crystal.

CRC-16

-Clock output function which can reflect the internal

CRC-16-CCCITT

high/low RC oscillator, HCLK, PLL output, and

CRC-32

external low clock.



Serial Wire Debug (SWD)



In-Circuit Programming (ICP) supported

Summary of Contents for SN32F280 Series













































































































































































































































































Search results

Summary of Contents for SN32F280 Series

Reviews:

Related manuals for SN32F280 Series

Brands by name

Popular brands

SONIX SN32F280 Series, User Manual

Search results

Summary of Contents for SN32F280 Series

Reviews:

Related manuals for SN32F280 Series

Brands by name

Popular brands