SONIX SN32F260 Series Page 84 User Manual Download | Manualshive

Page: 84 / 141

background image

SN32F260 Series

32-Bit Cortex-M0 Micro-Controller

SONiX TECHNOLOGY CO., LTD

Page 84

Version 1.5

7

7

7

WATCHDOG TIMER (WDT)

7.1 OVERVIEW

The purpose of the Watchdog is to reset the MCU within a reasonable amount of time if it enters an erroneous state.
When enabled, the Watchdog will generate a system reset or interrupt if the user program fails to "feed" (or reload) the
Watchdog within a predetermined amount of time.

The Watchdog consists of a divide by 128 fixed pre-scaler and a 8-bit counter. The clock is fed to the timer via a
pre-scaler. The timer decrements when clocked. The minimum value from which the counter decrements is 0x01.
Hence the minimum Watchdog interval is (T

WDT_PCLK

× 128 × 1) and the maximum Watchdog interval is (T

WDT_PCLK

× 128

× 256).

The Watchdog should be used in the following manner:
1.

Select the clock source for the watchdog timer with WDTCLKSEL register.

2.

Set the prescale value for the watchdog clock with WDTPRE

bits in

APB Clock Prescale register 1

register.

3.

Set the Watchdog timer constant reload value in

register.

4.

Enable the Watchdog and setup the Watchdog timer operating mode in

register.

5.

The Watchdog should be fed again by writing 0x55AA to

register before the Watchdog counter

underflows to prevent reset or interrupt.

When the watchdog is started by setting the WDTEN in

register, the time constant value is loaded in the

watchdog counter and the counter starts counting down. When the Watchdog is in the reset mode and the counter
underflows, the CPU will be reset, loading the stack pointer and program counter from the vector table as in the case of
external reset. Whenever the value 0x55AA is written in

register, the WDT_TC value is reloaded in the

watchdog counter and the watchdog reset or interrupt is prevented.

The watchdog timer block uses two clocks: HCLK and WDT_PCLK. HCLK is used for the AHB accesses to the
watchdog registers and is derived from the system clock. The WDT_PCLK is used for the watchdog timer counting.
Several clocks can be used as a clock source for WDT_PCLK clock: IHRC, ILRC, and HCLK.

The clock to the watchdog register block can be disabled in

AHB Clock Enable register (SYS1_AHBCLKEN)

register

for power savings.

Watchdog reset or interrupt will occur any time the watchdog is running and has an operating clock source.

«
...
82
83
84
85
86
...
»

Summary of Contents for SN32F260 Series














































































































































Reviews:

No comments

Related manuals for SN32F260 Series

Brand: Banner Pages: 15

Brand: Cypress Pages: 2

Brand: Dudley Pages: 8

Brand: Dukane Pages: 30

Smart Pass FPS-1000R

Brand: AHA Pages: 36

Infilex ZM WY5122

Brand: Azbil Pages: 12

Brand: AlfaRadio Pages: 23

CY3280-20x66 Universal CapSense

Brand: Cypress Pages: 2

Brand: Pulsafeeder Pages: 24

Anafaze PPC-2000

Brand: Watlow Pages: 320

Brand: V2 Pages: 108

ProCommander ES

Brand: WEIGL Pages: 12

Leroy-Somer R121

Brand: Nidec Pages: 16

LED PSU-5A Artnet/DMX

Brand: EuroLite Pages: 25

Brand: Phoenix Contact Pages: 82

Brand: Eliwell Pages: 4

Brand: CBS ArcSafe Pages: 8

Liebert Load Bus Sync Controller

Brand: Vertiv Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands