background image

SONANCE 

|

 

PROFESSIONAL SERIES

 

PENDANT

 

|

 INSTALLATION MANUAL 

6

INSTALLING THE SPEAKERS USING 

GRIPPLE SUSPENSION SYSTEMS

1.  Thread Gripple onto cable  
  (see inset detail). Pass over  
  ceiling anchor  point 
  (as shown) or through  
  other secure anchor point 
  of the building structure.  
  Installer is responsible for 
  ensuring that anchor point 
  is secure to building structure. 
  

(See figure 4)

.

2.  Thread cable through top  
  cover of speaker. 
  

(See figure 5)

.

 

6.  After height adjustment is  
  final, trim any unneeded  
  extra cable tail wires with  
  trimmer suitable for 2mm  
  (0.077 in) diameter   
  stranded aircraft-type 
  cable. Screw back on top  
  cover of speaker after  
  speaker wire is connected. 
  

(See figure 9)

.

3.  Pass tail end of cable  
  through the other  
  channel of the Gripple. 
  

(See figure 6)

4.  With speaker supported,  
  snap main support hook  
  hanger onto the center  
  hole in the top bracket  
  of the speaker. Adjust to  
  proper height by pulling  
  cable through either end  
     of Gripple. 

(See figure 7)

.

7.  Make sure the weight of  
  the load is supported. 
  

(See figure 10)

.

8.  Insert key into small hole at  
  bottom of Gripple. Push in  
  1/4” to release the cable. 
  

(See figure 11)

.

9.  Adjust height. 

(See figure 12)

.

10. Remove key and re-secure  
  the load. 

(See figure 13)

.

FIGURE 4: THREAD GRIPPLE

FIGURE 8: SECONDARY SUPPORT

FIGURE 9: SCREW ON COVER

FIGURE 10: LOAD SUPPORTED

FIGURE 11: RELEASE CABLE

FIGURE 12: ADJUST HEIGHT

FIGURE 13: REMOVE KEY

FIGURE 5: THREAD CABLE

FIGURE 6: THREAD CABLE AGAIN

FIGURE 7: MAIN SUPPORT

5.  Snap secondary support  
  safety cable hook hanger  
  onto one of the side holes  
  in the top bracket of the  
  speaker, and attach the top  
  to a different ceiling support  
  point of the building  
  structure, per Steps 1 & 2. 
  

(See figure 8)

.

 

HOW TO USE RELEASE 

KEY TO ADJUST HEIGHT 

OF SPEAKER

CAUTION: INSTALLATION MUST BE DONE BY QUALIFIED PERSONS 
USING SAFE RIGGING STANDARDS. USE EQUIPMENT ONLY IN 
ACCORDANCE WITH MANUFACTURER’S INSTRUCTIONS. DO NOT 
ALTER OR MODIFY. DO NOT USE EQUIPMENT IF THE EQUIPMENT 
IS NOT FUNCTIONING CORRECTLY OR IF THE EQUIPMENT 

 

IS DEFECTIVE.

Summary of Contents for PS-P43T















Reviews: