Sonance BPS-1, Installation Manual, Page: 5 / 8

5. Make sure the Vent Tube Clamp is positioned
around the neck of the Bandpass Connector and
tighten the clamp to secure the Vent Tube
around the neck of the Bandpass Connector.
6. After confirming that the Vent Tube is securely
fastened around the neck of the Bandpass
Connector, push the Bandpass Connector into
the Panel Bracket speaker opening.
7. Use the hardware included with the Bandpass
Connector to attach it to the Panel Bracket (see
Figure 11 ):
a) Apply a drop of Locktite to each hex screw.
b) Use the hex wrench included with the
Bandpass Connector to hand-tighten the hex
screws and secure the Bandpass Connector to
the Panel Bracket.
N
O T E
: T
H E I N C L U D E D
L
O C K T I T E I S R E Q U I R E D T O
P R E V E N T T H E H E X S C R E W S F R O M C O M I N G L O O S E
D U R I N G O P E R A T I O N
Speaker Connections
I M P O RTA N T : T
H E
B P S - 1
I S S P E C I F I C A L L Y D E S I G N E D
F O R U S E W I T H T H E
S
O N A M P
A 1 5 0
A M P L I F I E R
,
W H I C H
H A S L I M I T E R C I R C U I T R Y T H AT P R E V E N T S T H E
B P S - 1 ’
S
W O O F E R D R I V E R F R O M B E I N G D A M A G E D B Y A M P L I F I E R
C L I P P I N G
. U
S E O F A N Y O T H E R P O W E R A M P L I F I E R W I T H
T H E
B P S - 1
C O U L D R E S U L T I N D A M A G E T O T H E
W O O F E R A N D W I L L V O I D T H E
B P S - 1 ’
S WA R R A N T Y
.
1. Run the speaker wire from the A150 amplifier
to the BPS-1 cabinet.
N
O T E
: R
E F E R T O T H E
A 1 5 0
I N S T R U C T I O N
M A N U A L F O R I N F O R M A T I O N A B O U T A M P L I F I E R
C O N N E C T I O N S
.
2. Pass the speaker wire through the BPS-1’s
built-in wire tie, and route the wire’s end to
the speaker connector panel (see
Figure 12 ).
1. Apply Locktite
to Screws
2. Tighten Screws
with
Hex Wrench
Figure 11: Attach the Bandpass Connector to the Panel
Bracket
V E RY I M P O RTA N T
U
S E O N L Y T H E S U P P L I E D H A N D
-
H E L D H E X W R E N C H T O AT TA C H T H E
B
A N D PA S S
C
O N N E C T O R
.
D O N O T U S E A N E L E C T R I C S C R E W D R I V E R O R D R I L L .
N E V E R
O V E R
-
T I G H T E N T H E
B
A N D PA S S
C
O N N E C T O R M O U N T I N G S C R E W S
. O
V E R
-
T I G H T E N I N G T H E S C R E W S C A N
F R A C T U R E T H E
B
A N D PA S S
C
O N N E C T O R A S S E M B L Y
. T
H I S T Y P E O F D A M A G E I S
N O T
C O V E R E D B Y T H E
A
R C H I T E C T U R A L
S
E R I E S
W
A R R A N T Y
.
Page 5 of 8
Figure 12: BPS-1 Wire Management
and Speaker Connection
Sonance Architectural Series ®
BPS -1 IN-CEILING SUBWOOFER
I N S T A L L A T I O N M A N U A L