33
EN -Functions / H - Funkciók / SK - Funkcie / RO - Funcţii / SRB-MNE - Funkcije / CZ - Funkce /
HR-BIH - Funkcije
ELECTRIC FIREPLACE
FEATURES
● Panoramic fireplace with built-in fan heater for heating indoor air ● cosy flame effect ● adjustable brightness● built-in LED light
source ● 900 W / 1800 W heating power ● electronic thermostat and weekly program ● window opening detection ● overheating
protection
OPERATION
When switching on the unit for the first time, you may smell a slight odour, which is a natural phenomenon. It is harmless and
disappears fast.
The appliance can be operated using the buttons located on it or the remote controller.
Insert two AAA batteries into the remote controller.
Turn on the machine using the power switch. Now you can switch on the appliance using the on/off button of either the appliance (5) or
the remote controller (15). Realistic flame effect turns on and the display shows the room temperature.
Press the button on the appliance (6) or the remote controller (12) to turn on heating. Heating level indicator: H2 – high heating level,
H1 – low heating level. When heating is turned off, the fan may continue to run for 30 seconds.
You can set the thermostat between 15 and 30°C using the appropriate button on the appliance (7) or the remote controller (16). If the
room temperature is higher than the set temperature, the heating will turn off.
You can switch off or on the realistic flame effect using the button either on the appliance (8) or on the remote controller (21).
To adjust the brightness of the flame effect, press the brightness button (20) on the remote controller. The display shows the indication
of the selected brightness: H – high, C – medium, L – low.
To set the time, press and hold the clock button (20) on the remote controller. Then press the clock button again and use the +/- buttons
on the remote controller to select the appropriate day of the week. Press the clock button again, then use the +/- buttons to set the
hour for the current time, then press the clock button again and use the +/- buttons to set the minutes. Pressing the clock button again
will save the current time.
Setting a timer
You can set two on/off cycles for each day of the week on the appliance. Press and hold the M button (19) on the remote controller to
set one. Now you can first use the +/- buttons to set the hour of the start-up time ( ) for the first program (M1) on Monday (Mon).
After pressing the clock button (20), you can set the minute value. By pressing the clock button again, you can set the hour, and then
the minute for turn-off time ( ) of the first program on Monday. Then press the clock button to set the start-up and turn-off times for
the second program (M2) on, as described above. You can then set the start-up time for the first program (M1) on Tuesday (Tue) by
pressing the clock button again, and so on. If no key is pressed for 10 seconds, the appliance will exit the timer setting menu and the set
values will be saved. If you set 00 for the start-up or turn-off time for a cycle, the cycle will be skipped in the program. You can turn on
the timer function at any time during normal operation by pressing the M button on the remote controller. The active timer is indicated on
the display by the clock symbol (13). When the appliance runs as programmed, it operates according to the last set thermostat value.
The built-in energy saving, electronically controlled LED light source does not require replacement and cannot be replaced.
Overheating protection
serves to switch off the device in the event of overheating, e.g. if the air inlet or outlet is blocked. Disconnect
the device by pulling out the mains plug. Let the device cool down (min. 30 minutes). Check if the air inlet and outlet are unblocked;
clean them if necessary. Turn on the device again. If the overheat protection keeps activating, disconnect the device by pulling out the
mains plug and contact an authorised service shop.
TECHNICAL SPECIFICATIONS
power supply: .............................................................230 V~ / 50 Hz
heating power [
]: ..................................................900 W / 1800 W
light source [ ]: ..........................................................LED, 5 W, non-replaceable
maximum power: ........................................................1805 W
IP protection: ..............................................................IP20: The device is not protected against ingress of water.
heater dimensions: .....................................................107 x 43,5 (50) x 13 (24) cm
weight: ........................................................................18,6 kg
sound pressure ...........................................................58 dB (A)
