22
EN -Functions / H - Funkciók / SK - Funkcie / RO - Funcţii / SRB-MNE - Funkcije / CZ - Funkce /
HR-BIH - Funkcije
SMART FREE STANDING CERAMIC HEATER
FEATURES
smart ceramic heater for heating indoor air ● control via touch buttons, remote controller or a free smartphone app ● adjustable
output, 1000 W / 2000 W ● electronic thermostat ● shut-off timer for 12 hours ● free standing design ● switch-off in case of tipping ●
overheating protection
FAN OPERATION
The device can be controlled via its touch buttons, a remote controller or a free smartphone app.
Activate the main switch (1) on the side of the unit. The device beeps and the display shows the measured temperature. You can turn
on the appliance using the on/off button (8) on the remote control or the appliance.
You can turn the oscillation function on or off using the appropriate button (4) on either the appliance or the remote controller.
You can set the desired thermostat value between 15-45 °C using the appropriate button (4) on either the appliance or the remote
controller. If the set temperature is 2 °C higher than the room temperature, the appliance will start heating at low heating stage. If
the set temperature is 4 °C higher than the room temperature, the appliance will start heating at high heating stage. Once the room
temperature has reached the setting value, the appliances will switch to fan mode. You can select a heating stage independently of the
thermostat setting by using the corresponding button (7) on the appliance.
You can set the shut-off timer using the appropriate button (6) on either the appliance or the remote controller.
SMARTPHONE APPLICATION:
The mobile phone must be connected to the Internet.
1. Scan the QR code with your phone (Figure 3.), then download and install the „Tuya Smart” application.
2. Select the country code and enter your mobile phone number, then press the „Get” button.
3. Enter the („verification code”) you received in SMS, and enter the password you want to use for the application containing numbers
and letters.
4. Enter the application: „Login”
5. Make sure that your device and smartphone are as close as possible and connected to the WIFI router.
6. Press the „+” button to add the new appliance to the program.
7. Select the type of the appliance: „Small home appliances”
→
„Heaters”
8. Press and hold the WIFI reset button (7) on the heater until the WIFI symbol starts to flash on the display of the heater.
9. Enter the password of the WIFI network you want to use on your appliance, then press the „Next” button.
10. Select in the application that the heater’s WIFI indicator blinks quickly. After this, pairing runs, the heater connects to the cloud-
based application.
Using the application, you can control all functions of the device.
You can disconnect the heater anytime from the cloud-based application. For this, press and hold the heater’s or the remote control’s
WIFI reset button until flashing quickly, the heater beeps once.
In the event of overheating, the
overheating protection function
switches off the unit. Power off the unit by unplugging it from the
electric outlet. Allow the appliance to cool down (min. 30 minutes). Check whether the air inlet and outlet openings are obstructed or not,
and clean them if necessary. Reinstall the appliance. If overheating protection activates again, power off the appliance by unplugging
its power plug and contact a service facility.
A switch on the bottom of the appliance turns it off if it should topple over. In such cases remove power from the appliance by pulling
out the power plug then stand the appliance upright and reinstall it only afterwards according to the section entitled INSTALLATION.
TECHNICALSPECIFICATION
power supply: ....................................................220-240 V~ 50/60 Hz
output.................................................................1000 W / 2000 W
IP protection: .....................................................IP20: The appliance is not protected against ingress of water.
dimensions heater: ............................................
23 x 56 x 15 cm
transmission frequency ......................................2,4 GHz / 1 mW
noise level: ........................................................60 dB(A)
weight: ...............................................................
2 kg
length of power cable: .......................................1,4 m