23
EN -Functions / H - Funkciók / SK - Funkcie / RO - Funcţii / SRB-MNE - Funkcije / CZ - Funkce /
HR-BIH - Funkcije
SMART HEATER WITH TOWEL DRYER
FEATURES
smart infrared heating panel for heating indoor air and drying towels ● control via touch buttons or smartphone application ● 850 W
output ● electronic thermostat ● weekly program ● child lock ● IPX4 protection from water splash ● glass front panel ● metal towel
rail ● wall mounted design ● automatic shut-off in case of overheating
OPERATION
The device can be controlled via its touch buttons or a free smartphone app.
Using the touch buttons of the device: After connecting the device to the mains, turn it on using the main switch. The device briefly
beeps. You can use the button to turn the device
on/off
. You can check the measured temperature on the left side, and the set
temperature value on the right side of the display. Use the touch buttons (7) of the device to set the desired temperature between
5
and 40°C
. Once the room temperature has reached the setting value, the device stops to heat. The device will turn on again when the
room temperature drops 2 °C below the setting value. You can select the
heating mode
using the button (6). The selected heating
mode is indicated by or
on the device display. In mode, the device can heat up to 55 °C, while in mode, it can heat up to
75 °C. Repeatedly press the button to set the
remaining operating time i
n hours, up to 24 hours. You can enable or disable the
child lock function by pressing and holding the child lock button (4) for 3 seconds.
If power failure occurs
or the device is switched off
using the main switch, all settings will be reset, including the child lock. After switching on, the default thermostat temperature setting
is 25°C. When the button is used to switch off the device, the thermostat and heating level settings are retained, and the switch-off
timer countdown continues to run.
With smartphone application. The mobile phone needs to be connected to internet.
1. Scan the QR code (
5. figure
) with you smart phone then download and install “Tuya Smart” application.
2. Select the country dialing number, enter your mobile phone number and press the “Get” button.
3. Enter the “Verification code” you got in SMS and enter the password you want to use in the application, which should consist of
numbers and letters.
4. Login to the application: „Login”
5. Make sure your appliance and smartphone are as close as possible to the wifi router and both are connected to it.
6. Add the new appliance to the program by pressing the “+” button.
● Select the appliance type: “Heater”.
● Press the “Finish network configuration” button.
● Press and hold the button for more than 5 seconds until the beep sound
● Tick the check box, and press „Next: Connect appliance with Wi-Fi” button
● Enter the Wi-Fi password, and press the „Confirm” button.
● Press and hold the button for more than 5 seconds until the beep sound.
The appliance is connecting the cloud based application.
7. If the connection under the 6. point was not successful, “Failed to add” is displayed.
● Choose the lower „Add appliance with other methods” possibility.
● Press and hold the button for more than 5 seconds until the beep sound.
● Press the „Finish network configuration” button.
● Tick the check box, and press „Next: Connect appliance with Wi-Fi” button
● Enter the Wi-Fi password, and press the „Confirm” button.
● On the appearing „Connect phone to appliance’s wifi hotspot” screen, choose the „Connect now” option.
● Press and hold the button for more than 5 seconds until the beep sound, until the WLAN network shows up the „SmartLife-
XXXX” network. Choose this for the connection. If the status is „Connected”, then press the step back button on the mobile.
● The „Connecting now” screen runs down, and the appliance is connected to the cloud based application.
8. In the application, you can see the room temperature, you can switch on/off the appliance, you can choose low (Low) or high (High)
heating stage, you can switch the child lock on/off, you can set switch off timing, and you can set the exact times and dates for
switching the appliance on and off.
In the event of overheating, the
overheating protection function
will switch off the appliance, for example when the air inlets and
outlets are covered. Power off the appliance by unplugging it from the electric outlet. Allow the appliance to cool (for at least 30
minutes). Check whether the air inlets and outlets are obstructed or not, and clean them if necessary. Install the appliance again. If the
overheating protection activates again, power off the appliance by unplugging it from the electric outlet and contact the service facility.
