27
CAR RADIO AND MP3/WMA PLAYER
MAIN QUALITIES
• FM / BT / MP3 / WMA / USB / SD / AUX • Wireless BT connection • Listening to music from mobile phone, tablet • Controlling the mobile device's
music player • Making phone conversation without touching the phone • Making phone conversation hands-free • Ringtone is audible through the
cars’ speakers • Displaying caller phone number on the display • Announcement of caller ID in English • Answering calls / ending calls / redialling
the last numbers • Well readable text display • 18 FM memories • Manual or automatic station seeking and storing • Displaying current time even in
switched off position • Playing modes: introducing songs, repeating, random playing • Handling folders • Tone, loudness and EQ sound settings • 4 x
45 W Hi-Fi speaker output • 3,5 mm AUX input for portable appliances • 4 x RCA socket to connect amplifier, subwoofer • Remote controller (CR2025,
3 V button cell, included)
RESETTING THE UNIT
The microprocessor data requires resetting in situations where the power supply is lost or the unit (including its display) acts erratically. In order to
do so, press the
RESET
button for 3 seconds, located on the front panel using a thin, sharp object. The equipment will switch off and will return to
factory default condition. This operation is required after installation, before switching on the unit for the first time, furthermore when the vehicle’s
battery is replaced.
ON- AND OFF SWITCHING
In case of proper connection, current time is visible on the display in switched off position. To switch on the unit, press
POWER/MUTE
button briefly. To
switch it off, keep holding it for 2 seconds. With brief pressing of it, you can mute the speakers (MUTE).
• Later on, it will automatically switch to the most recently used function after being switched on unless the external storage device has been removed
in the meantime.
• Since voltage surges can occur when the vehicle’s engine is started, only turn on the unit after the engine has been started. Turn off the unit before
stopping the engine.
VOLUME AND TONE SETTING
Use the
rotating knob
to set the desired volume level:
VOL
. Press briefly, repeatedly the
rotating knob
, till the desired volume or tone function appears
on the display. After you can modify setting by rotating the knob.
• Available sound settings:
VOL:
volume /
BASS:
bass tone /
TREBLE:
treble tone/
BALANCE:
left-right channel /
FADER:
front-rear channels /
LOUD-
NESS:
on/off /
EQ:
on/off and modes (POP-CLASSIC-ROCK-OFF) / STEREO-MONO / DX-LOCAL
•
EQ ON:
in switched on EQ mode, the traditional high-low (TREBLE, BASS) equalizer is not available.
•
EQ OFF:
in order to use treble-bass equalizer, switch off the EQ settings.
• When listening to music on higher volume, do not emphasize significantly high and low tones, as this may cause distortion!
LOUDNESS - PHYSIOLOGICAL TONE ADJUSTMENT
The human ear perceives less of low and high frequency sounds at smaller volume. By turning
LOUDNESS
function on, at low volume, automatic tone
adjustment depending on volume, will correct this effect. The lower the volume, the higher the bass and treble frequency boost. It is recommended to switch
off this function at higher volume, since it may cause distorted sound.
• In order to get better sound quality, before using this function it is recommended to choose EQ OFF setting, and set the equalizers to „0” position.
• The larger the volume, the less noticeable effect on the automatic tone correction.
SETTING THE CURRENT TIME
Switch on the unit with
POWER/MUTE
button, then press
ENTER
button on the remote controller to display the clock. Before it would disappear, press
it again for 2 seconds, and hour display will start flashing. Set the number of hours with the rotating knob or with
VOL+/-
buttons of the remote controller,
then press
ENTER
button for storing, and step forward to setting minutes. While the minute’s display is flashing, set it also, as written above. Finally
keep holding
ENTER
button or wait till the setting is stored and for exiting.
• If you are waiting for more than 4 seconds idly during settings, the unit will exit that menu.
• Current time is visible on the display, when the unit is switched off.
• When the unit is switched on, current time can be displayed with DISPLAY button, which is visible for 5 seconds.
SELECTION OF DATA SOURCE
You can select the desired data source by repeated brief pressing of
MODE
button. Available options: radio - USB – SD –
∅
3,5 mm AUX external
input – wireless BT connection
• Desired signal source cannot be activated, if it is not available. For example there is no USB or SD storage connected, where the adequate MP3/WMA
files are available.
• If there is external unit connected to USB and SD slot at the same time, then USB or SD option can be selected with MODE button. Basically SD card
is recommended to use, because of its safe location.
• After connecting external data sources, tracks from the last inserted one will be played.
• Being switched on again, playing of last listened track will continue, if the connected device has not been removed in the meantime.
USING THE RADIO
After the unit is switched on the radio will turn on if it was being previously listened to – or the last played USB/SD signal source has been removed. If neces
-
sary, use the
MODE
button to select radio function.
SELECTION FROM THE STORED RADIO STATIONS
Select desired band with
BAND
button, (e.g.
F1
), then select the desired programme with
1…6
number keys. Totally 18 FM radio stations can be
memorised/stored.