Sommerkamp TS-340 DX Owner'S Manual Download Page 2

G EN ER AL

Your  new  Sommerkamp  TS-340  DX  is  a  Professional  quality  Citizens  Band  Transceiver  designed  to 

operate  on  either  AM,  Lower  Single  Sideband  (LSB)  or  Upper  Single  Sideband  (USB).  It  has  many 

innovative  engineering  and  user  functïons.  Among  them,  a  Sommerkamp  plus feature  is  an  amplified 
AGC  circuit,  built  in  to  your  TS-340.  This  expands  the  range  of  a  normal  AGC  circuit  by  many 

times,  and  is  usually  found  only  in  the  most  expensive  sets.  Your amplified  AGC will  enable  you  to 

hear  clearly,  even  a  very  weak  distant  signal,  and  still  allow  you  to  hear  a  unit  close  by  without 
overload.  The  PLL  (phase  lock  loop)  frequency  Synthesizer  is  the  heart  of  the  TS-340  DX's  rock 
steady  frequency  control.  The  PLL  is  self compensating  for frequency d rift,  keeping your TS-340  DX 
on  center  channel,  every  channel.  Careful  reading  of  this  instruction  manuał  before  operation  is 

essential  for  proper operation  and  prévention  of  damage.

PACKING

This  unit  has  been  especially  protected  for  shipment.  Open  the  carton  carefully  to  avoid  damage. 

Examine  the  unit  for  any  visible  damage.  If  the  transceiver  has  been  damaged  in  shipment,  save the 

box,  and  packing  material,  and  n o tify  the transportation  company.

RECEIVER

Sensitivity  o f  less  than  a  1/2  of  a  microvolt  on  SSB  and  AM.  A  tuned  RF  stage  pulls  in  even  the 

weakest signais.

A  deluxe  filte r  on  SSB  provides  the  highest  degree  of selectivity  and  rejection  of unwanted  adjacent 
channel  signais.  Ceramic  Filters  for  AM  réception  deliver  over  70  db  adjacent  channel  rejection. 
Additional  receiver  features  include:  variable  squelch,  clarifier  control,  integrated  circuit  audio 
preamplifier  stage,  metering  automatic  noise  eliminator.

TRANSMITTER

High  efficiency  is  obtained  through  use  of  select  components  and  sophisticated  engineering  design. 

An  ALC circuit  is employed  in  the  SSB  mode to  provide maximum  "Talk  Power" w ithout distortion. 
The  SSB  signal  is 

by  use  of  an  integrated  circuit  balanced  modulator  and  PLL

Synthesizer,  to   keep  you  on  center  channel,  every  channel.  Electronic  switching  is  employed  for 

dependability.

POWER  SUPPLY

Either Positive or  Negative ground  12  Volts  DC  (13.8  VDC  E!A)  is built  in.

1

Summary of Contents for TS-340 DX


















Reviews: