SOMMER SPA-2 Manual Download Page 49

Page: 49 / 111

10 Configuration

The SPA-2 can be configured with one of the following tools:

Configuration with Commander support software

Configuration with a terminal program

10.1 Configuration with Commander support software

Follow the steps below to modify the configuration parameters of the SPA-2:

1. Establish a connection between your PC and the SPA-2 as described in

Connect the SPA-2 to

a PC

Select the tab

Parameters (F2)

and click

Download parameters from device

. The complete

parameter list is transferred from the sensor to your PC and displayed in the Parameter win-
dow.

NOTE

The first download of the parameter list may take a few

minutes. After that the device is known to the PC and consecutive
downloads are much faster.

fig

Manual

Summary of Contents for SPA-2















































































































Search results

Summary of Contents for SPA-2

Reviews:

Related manuals for SPA-2

Brands by name

Popular brands

SOMMER SPA-2, Manual

Search results

Summary of Contents for SPA-2

Reviews:

Related manuals for SPA-2

Brands by name

Popular brands